The FAB-1100 is installed in the GI-3821 in accordance with instructions provided with that appliance. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Factory Supplied Not Supplied with Blower Kit Blower Plug Junction Box ON/OFF Wall Switch 120Vac 60Hz} Factory Supplied Not Supplied with Blower Kit Blower Plug Junction Box ON/OFF Wall Switch 120Vac 60Hz} APPLIANCE WIRING Most appliances are fitted with an electrical "J" box that can be accessed from outside of the appliance outer wrapper at the tim

n Use medium to higher throttle settings to move grass or leaves from parking lots or walkways. n Use full throttle when moving heavy loads such as dirt or snow. IMPORTANT! Blower noise increases at higher throttle settings! Always use the lowest throttle setting required to get the job done! Wear eye protection that meets ANSI Z87.1 such as a face shield or goggles while operating this machine! Wear close-fitting clothing to protect your legs and arms, and Do not wear clothing or jewelry that c

Muffler Body 48016D First, remove the spark plug Remove the Engine Cover Muffler Screw Retaining Tab Engine Cover Engine Cover 48018 Arrester Screen 5 mm Lower Screw 6 mm Muffler Screws Remove four Allen- head capscrews Figure 15 Gasket WARNING! Never operate the machine with a damaged or missing muffler or spark arrester! Operating with missing or damaged exhaust components is a fire hazard and could also damage your hearing. Exhaust Tube Tail Cap Mounting Screws Figure 16 Remove the Muffler. 1

n LUBRICATION Remove the spark plug, and then pour approximately 1/4-oz of 2-cycle oil into the cylinder through the spark plug hole. Before reinstalling the spark plug, pull the recoil starter gently 2–3 times to distribute the oil over the cylinder walls. n AIR CLEANER Remove, clean, and reinstall the filter element as described under “daily maintenance.” n STORAGE Store the blower in a clean, dry, dust-free environment. CAUTION! Never store this product with any fuel remaining in the tank, fu

Always wear eye and hearing protection when operating this unit. Minimize the risk of injury: Read this manual and familiarize yourself with its contents. Part Number 68232-94011 Rev. 11/06 CONTENTS INTRODUCTION IMPORTANT! Before using this product, consult local regulations concerning noise restrictions and hours of operation! The Shindaiwa EB501 has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety, or durability. Shindaiwa h

See figure 7. 4. Using your right hand, pull the starter handle slowly until you feel the starter engage. 48006 Throttle Positions Full Throttle WARNING! The engine cover will be hot after blower operation! Engine Idle Lock Lever Stop Figure 5 Choke Control (open position shown) 48008 48007 Pull upward rapidly Fuel Primer Bulb Figure 7 Figure 6 8 5. As the starter engages, pull the starter handle upward rapidly. 6. If necessary, repeat Steps 4 and 5 2–3 times until the engine starts. WHEN THE EN

WARNING! WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. • ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. • DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit. • NEVER reach into any opening while the engine is running. Moving parts may not be vi

Assembling the Blower WARNING! Danger from rotating impeller! Stop the engine before installing or removing the blower tubes! Never perform any maintenance or assembly procedures on this unit while the engine is running! Place the blower upright on the ground or on a sturdy work surface. 1. Grasp the blower tube as shown, and push the tube over the blower discharge port and locking pins. 2. Lock the blower tube to the blower discharge port by rotating the tube as shown. Blower Tube Locking Pin P

Always wear eye and hearing WARNING! protection when operating this unit. X7501920300 2 Table of Contents CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to avoid damaging the unit. CAUTION! This blower is equipped with a spark-arresting muffler! Never operate this unit without both the muffler and spark arrester installed and properly functioning! WARNING! The engine exhaust from this unit contains chemicals known to the state of California to

• If you are unfamiliar with this engine or uncomfortable with this procedure, consult with an authorized Shindaiwa servicing dealer. 1. Remove cylinder cover, rocker arm cover, and set piston at TDC-compression. 2. Loosen adjuster locknut so that the 2.5 mm Allen socket head adjustment screw can turn freely. 3. Insert 0.10 mm (0.004 in.) feeler gauge between valve stem tip and rocker arm. 4. Turn adjustment screw (clockwise = tighter, counter-clockwise = looser) until feeler gauge is almost snu