Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
180 CFM ........................................................................................................................................................................ 375 FEATURES KNOW YOUR BLOWER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. MOTOR The blower has a powerful 30cc engine with sufficient power to handle tough blowing jobs. THROTTLE TRIGGER The blower can be operated at any speed between idle and full throttle. TRIGGER LOCK The trigger lock feature is used for easier starting and also allows the user to operate the blower without holding the throttle trigger. To disengage the trigger lock, simply depress the throttle trigger. BLOWER TUBES The blower tubes can be assembled and installed on the blower using no tools. WIDE SWEEPER NOZZLE The wide sweeper nozzle allows for more area to be covered during blower operation. WIDE SWEEPER NOZZLE STRAIGHT TUBE STRAIGHT TUBE THROTTLE TRIGGER SWITCH BLOWER HARNESS STRAPS BELLOWS CONTROL HANDLE TRIGGER LOCK CABLE TIE ENGINE ELBOW UPPER TUBE SMALL CLAMP LARGE CLAMPS Fig. 1 ASSEMBLY ASSEMBLY This product requires assembly. ¦ Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. ¦ Inspect the product carefully to make sure no breakage or damage occurred during shipping. ¦ Do not discard the packing material until you have carefully inspected and satisfactorily operated the product. ¦ If any parts are damaged or missing, please call 1-800-2424672 for assistance. WARNING: If any parts are missing do not operate this product until the missing parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. PACKING LIST Blower Elbow Bellows Upper Tube Large Clamps (2) Small Clamp Cable Tie Straight Tubes (2) Nozzle Harness Straps (2) 2-Cycle Engine Oil Operator's Manual NOTE: Read and remove all hang tags and store with your Operator's Manual. Page 7 Page 8 WARNING: Disconnect the spark plug wire before assemblying parts. Failure to do so could result in possible serious personal injury. ASSEMBLING THE BLOWER TUBES See Figures 2 - 5. ¦ Place large clamp on the elbow tube and install the elbow tube onto blower. Tighten large clamp securely. ¦ Place large clamp on the bellows and install the bellows onto the elbow. Tighten clamp securely. ¦ Insert upper tube into throttle control handle. Position the throttle control handle in the center of upper tube and tighten wing nut securely. NOTE: The position of the throttle control handle may be adjusted for the best comfort after the blower is strapped onto the operator's back. ¦ Place small clamp on the bottom end of the bellows and install the upper tube onto the bellows; tighten clamp securely. ¦ Join two straight tubes, thread into the upper tube and tighten securely. ¦ Thread nozzle onto tube assembly and tighten securely. ¦ Tighten all threaded joints securely. NOTE: Check all threaded joints after initial run to ensure they are tightened securely. ¦ Hold the throttle cable against the bellows and install the cable tie. Cable tie should be tight enough to retain the throttle cable to the bellows but still allow for movement. Fig. 3 ASSEMBLY CONTROL HANDLE WING NUT THROTTLE CABLE Fig. 4 UPPER TUBE BELLOWS ELBOW TUBE LARGE CLAMP LARGE CLAMP Fig. 2 UPPER TUBE CONTROL HANDLE THROTTLE CABLE SMALL CLAMP BELLOWS Page 9 ASSEMBLING HARNESS STRAPS See Figures 6 - 7. ¦ Place short looped end of the harness strap through the top bracket. Open loop and slide onto extruded end of the bracket. ¦ Lace long end of the harness strap through the slot in the backpack frame. ¦ Thread the harness strap end through the center of buckle and then through the top toothed portion and tighten. ¦ Repeat steps to attach the second harness strap to the blower. CAUTION: Make all adjustments to the harness straps before starting the blower to avoid the possibility of injury. ADJUSTING HARNESS STRAPS Harness straps should be adjusted to a comfortable position before starting the blower. To adjust the harness straps: ¦ Blower should be in operating position before adjusting the harness straps. Slip arm through harness strap and onto shoulder, then repeat for the other shoulder. ¦ Tighten or loosen each harness strap as needed, until they are adjusted to a comfortable operating position. ¦ Pull on harness straps to secure in buckle. SHORT LOOPED END OF STRAP EXTRUDED END OF BRACKET SLOT IN BACKPACK FRAME BUCKLE Fig. 6 ASSEMBLY Fig. 5 STRAIGHT TUBE STRAIGHT TUBE NOZZLE SMALL CLAMP Fig. 7 CABLE TIE TOP BRACKET OPERATIO N WARNING: Gasoline is extremely flammable and explosive. A fire or explosion from gasoline will burn you and others. M...
Эта инструкция также подходит к моделям:Системы вентиляции - BACKPACKER II UT08571 (1.2 mb)