Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
System Start-up: (purging air from system). Factory Fills unit with SAE 20W-50 multiviscosity motor oil. This will need to be checked when setting up with instructions below. At system start-up, several things need to be accomplished to ensure a properly running system. 1. Fill the BDU case and expansion level and ensure they do not empty during the following procedure. 2. Start engine and increase throttle to at least 2/3 speed. 3. Open bypass valve by depressing bypass plunger and holding. 4. Adjust control linkage such that transmission control is stroking full forward. 5. Move and hold control in forward for 3 seconds; repeat two additional times. 6. Close bypass valve be releasing bypass plunger. 7. With engine still at same speed, repeat step 5. 8. Move control to neutral. 9. Check engine speed. Adjust to recommended maximum engine speed. 10. Adjust neutral position. 11. Adjust forward control stop to recommended axle speed. 12. Adjust reverse control stop to recommended axle speed. 13. If axle speed is not achieved ensure linkage allows proper movement of transmission control. 14. If transmission control lever is rotating fully but recommended axle speed is not achieved, repeat start-up procedure. 15. Refill expansion tank oil to recommended level. 10 PARTS MAIN FRAME ASSEMBLY 11 PARTS SELF PROPELLED ASSEMBLY PARTS HANDLE ASSEMBLY SEEDER/MULTIPURPOSE BLADE ASSEMBLY QTY/PER KEY PART NO. MACHINE DESCRIPTION 1 700025 1 Shaft w/ Blade Holders, Multipurpose 2 100310 26 Blade w/ 15/16” Holes, Multipurpose 3 500216 52 Bolt, 5/16-18 x 314 Grade 8 4 500217 52 Nut, 5/16-18 Tap Lock 5 600030 1 Shaft/Blades Sub-Assembly, Multipurpose 6 900026 1 Complete Multipurpose Shaft Assembly (Includes Shaft, Blades, End Plates, Bearings, Pulley, Key & Fasteners) - Not Shown SLICER BLADE ASSEMBLY (OPTIONAL) QTY/PER KEY PART NO. MACHINE DESCRIPTION 1 700025 1 Shaft w/ Blade Holders, Multipurpose 2 300032 26 Blade, Slicer Square 3 500180 52 Bolt, 1/4-20 x 3/4 Grade 8 4 500160 52 Nut, 1/4-20 Top Lock 5 600024 1 Shaft/Blades Sub-Assembly, Multipurpose 6 900016 1 Complete Slicing Shaft Assembly (Includes Shaft, Blades, End Plates, Bearings, Pulley, Key & Fasteners) - Not Shown TSS-20 SEED BOX ASSEMBLY QTY/PER QTY/PER KEY PART NO. MACHINE DESCRIPTION KEY PART NO. MACHINE DESCRIPTION 1 500068 8 1/4” NYLOC NUT 18 500088 10 1/4” FLAT WASHER 2 100140 1 GAUGE w/ BOLT & WING NUT 19 900033 1 COMPLETE SEED BOX ASSEMBLY 3 500089 2 1/4” x 1-1/2” BOLT 20 500069 3 1/4” x 5/8” BOLT 4 100142 1 CONTROL LEVER GRIP 21 500227 1 3/16” FLAT WASHER 5 100141 1 CABLE CONTROL LEVER 22 300116 1 SIDE PLATE 6 500118 3 1/4” x 1-3/4” BOLT 23 400209 1 AXLE 7 100139 1 CONTROL CABLE (NOT SHOWN) 24 100356 2 BEARING 8 100127 1 FRICTION WASHER 25 500223 2 3/16 x 1” BOLT 9 100229 3 #8 x 3/4” BLACK SCREW 26 500224 3 3/16” NUT 10 100144 2 HOUSING CLIP 27 100358 2 SHUT-OFF END CLIP 11 100357 1 SEED BOX 28 100359 1 SHUT-OFF ASSEMBLY 12 500226 1 3/16 LOCK WASHER 29 100074 1 DECAL, “CLASSEN” 13 100355 2 8” SEED BOX DRIVE WHEEL 30 500225 1 3/16” x 3/4” BOLT 14 100067 2 SHAFT GUARD 31 100020 1 PLASTIC TIE 15 400038 1 MOUNTING BRACKET 32 400040 2 CONNECTING PINS 16 100078 1 VINYL SEED BOX COVER 33 500096 1 5/32” x 3” HAIR PIN 17 400039 1 STABILIZING BRACKET 34 500016 1 5/32” x 1-1/4” COTTER PIN SEEDER TIRE SCRAPE INSTALLATION SEED BOX INSTALLATION For shipping purposes only, the seed box assembly is attached to machine improperly. To set your machine correctly for operation, remove hairpin clip (A) from upper connecting rod (B). Slide upper rod out, allowing “A shaped” stabilizing bracket (C) on seed box to sit over lower connecting rod. (When mounted properly, wheels of seed box should be resting on front wheels of machine.) Reinsert rod and clip. SAFETY DECALS QTY/PER QTY/PER KEY PART NO. MACHINE DESCRIPTION KEY PART NO. MACHINE DESCRIPTION 1 100074 2 Decal, “Classen” 6 100341 1 Decal, “TSS-20” (Turf Seeder only) 2 100060 1 Decal, “CAUTION - Muffler and Shields 7 100069 1 Decal, “DANGER, Keep Hands and Feet Away” May Exceed 150°” 8 100070 1 Decal, “DANGER - Carbon Monoxide” 3 100340 1 Decal, “TRS-20” (Turf Rake only) 9 100138 1 Decal, “Seed Application Chart” (Turf Seeder only) 4 100071 1 Decal, “Bail Engagement” 10 100228 1 Decal, “CAUTION - Catcher Bag (Turf Rake only) 5 100061 1 Decal, “CAUTION - Operating Instructions” 11 100054 1 Manual, Operators/Parts (Not Shown) NOTES Schiller-Pfeiffer, Inc. 1028 Street Road • Southampton, PA 18966 Telephone: 1-800-366-6268 ONE YEAR LIMITED WARRANTY Effective January 1, 1994 For the period of one year from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser (90 days if used for rental purposes) free of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk, Nebraska, to be defective in material or workmanship. All transportation charges on parts submitted for repair or replacement under this warranty shall be borne by the p...
Эта инструкция также подходит к моделям:Системы вентиляции - TSS-20 (1.36 mb)
Системы вентиляции - TRS-20 (1.36 mb)
Системы вентиляции - TRS-20 (1.36 mb)