Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Системы охлаждения - 3D Galaxy II (7.07 mb)
Системы охлаждения - 3D Galaxy II (4.33 mb)
Системы охлаждения - 3D Galaxy II (4.98 mb)
Фрагмент инструкции
2-5 Place the MOSFET air cooling fan on the top of waterblock and make sure that the four feet of MOSFET air cooling fan are firmly locked to the waterblock. Quick Installation Guide Accessories 01) Radiator 02) Pump + Tank Assembly 03) MOSFET Air Cooling Fan 04) Waterblock 05) 4-Way Splitter Valve ( 2 pcs ) 06) 1/2 Inch Tube 07) Tube Clips ( 8 pcs ) 08) Screws 09) Intel® Pentium®4 LGA775 Spring Screws 10) Intel® Pentium®4 LGA775 Back Plate 11) Intel® Pentium®4 LGA775 Bracket 12) AMD K8 Clip 13) AMD Bracket 14) Fan Speed Control Box 15) PCI rear fan speed control panel 16) Radiator Rack 17) Pump Power Cord 18) Fan 1 to 2 Power Cord 19) Fan speed control Power Cord 20) Heat Sink for Memory ( 8 pcs ) 21) Bend Proof Spring 22) Nylon Tie ( 4pcs ) 23) Grease 24) GIGABYTETM Liquid Coolant 25) Velcro 26) Installation Guide GH-WIU02 < Figure a > < Figure b > 2-8 Place PCI slot fan speed controller at the rear of the chassis. (Place on the middle or lower PCI slot is recommended ) 2-9 Thread Tube 3 through the hole on PCI slot ( as Figure a ) to connect one side of tube 3 with 4-way splitter valve (1) B and fasten it with tube clips ( as Figure b ), and connect the other side of tube 3 with the inlet of radiator and fasten it with tube clips ( as Figure c ). Caution 1. For a detailed installation process, please refer to the complete version of the manual 2. Before pouring liquid coolant into the tank to test the liquid cooling system, please reconfirm all the tubes have been fastened and the tube clips are in the right position. 3. While the liquid in the tank is lower than the low water-level, the red light on the bottom of the PCB will blink. ( Please purchase GIGABYTETM liquid coolant to fill it ) 4. When the liquid is lower than the low water-level, the system will turn off automatically within four seconds after detection of water inadequacy. 5. While removing the tubes for disassembly, please make sure to keep all the devices away from any electronic part. ( Please refer to disassembly process instruction ) For GIGABYTETM 3D Aurora.Triton or Poseidon series chassis user, the tube can be threaded through drainage inlet / outlet on the chassis. ( as the right two holes in Figure d ) < Figure a > < Figure b > < Figure c > < Figure d > 2-10 Thread Tube 4 through the hole on PCI slot to connect one side of tube 4 with the outlet of radiator and fasten it with tube clips, and connect the other side of tube 4 with the inlet of the tank and fasten it with clips. After measuring the distance between the parts of the cooling system, cut the tubes into five suitable pieces as shown below. To get the right length for each tube, it is strongly recommended to fit all the components in the right position. Tube 3 Step 3 Pump Power Cord Installation Tube1 3-1 Connect the Power SW ( female 2-pin ) from the chassis’s panel with the pump power cord male 2-pin. 3-2 Connect the pump power SW cord female 2-pin with “+PW-“ jumper on the motherboard. Liquid Cooling System complete installation diagram a Tube3 : The inlet of radiator to 4-way splitter valve (1) Tube4 : The outlet of radiator to the inlet of the tank Tube 4 b B 2-11 Use tube 5 to be connect 4-way splitter valve with outlet of the tank and fasten it with tube clips. 3-4 Connect 4-pin power supply connector with the 4-pin pump cord connector. 3-3 Connect the pump power cord 6-pin connector with the back of the tank. ( as figure a / b ) A Tube 2 Tube 5 < Figure b > < Figure a > B Step 5 Radiator Speed Control Box Installation Pour in Liquid Coolant Step 4 Intel® Pentium4® LGA775 Back Plate Installation ( FOR AMD series CPU please ignore this step) Step 1 A Tube1 : 4-way splitter valve (1) to the outlet of the waterblack 5-1 Open the lid of the tank to pour in liquid coolant and close the lid. H Take off the double-side sticker on the Intel® Pentium®4 LGA775 Back Plate ( as Figure a ), and stick it on the back of Intel® Pentium®4 LGA775 CPU with aligning four holes on Intel® Pentium®4 LGA775 Back Plate and four holes on the back of Pentium4® LGA775 CPU motherboard (as Figure b). 5-2 Turn on the power until all liquid coolant drains into the tubes; the red light on the bottom of PCB will blink and bleep; the system will turn off automatically within 4 seconds. ( This is normal at this point since the tube and radiator are not full of liquid. ) 4-1 Thread the radiator fan connector through the hole of PCI slot fan speed control panel. Tube5 : 4-way splitter valve (2) to the outlet of the tank Tube2 : 4-way splitter valve (2) to the inlet of the waterblock Tube Installation Step 2 5-3 Open the lid of the tank again to refill it with liquid coolant and close it. Turn on the power one more time and repeat this step until the water is no longer lower than low water- level. 2-1 Connect one side of tube 1 with 4-way splitter valve (1) A as shown in the picture and fasten it with tube clip; connect the other side of tube 1 with the outlet of waterblock and fasten it with tube clip....