Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• When intro or ending is selected as the accompaniment pattern, the same rhythm is always assigned to all eight instrument parts. Because of this, performing rhythm assignment in step (1) for an intro or ending will change the rhythm of all instrument parts at one time. 6. Repeat steps 3 through 5 to edit other accompaniment patterns and instrument parts. 7. After editing is complete, adjust the tempo of the rhythm as desired. • The tempo you set here becomes the initial default tempo. 8. To save a rhythm after you edit it, hold down the R-13 (FUNCTION) button as you press the C-13 (MENU) button. • This displays the rhythm editor menu with the 0 located at “Store”. Using Auto Accompaniment Using Auto Accompaniment 9. After everything is the way you want, press the R-16 (ENTER) button. • This displays a screen for specifying the destination user rhythm number and rhythm name. Destination user rhythm number Rhythm name 10. Use the dial or R-14 (–, +) buttons to select the destination user rhythm number you want. 11. Use the R-17 (u, i) buttons to move the cursor to the name character position you want to change, and then use the dial or R-14 (–, +) buttons to select the character you want. • See “Supported Input Characters” (page E-124) for information about the characters you can input for the name. • To input a space, press both of the R-14 (–, +) buttons at the same time. 12. Press the R-16 (ENTER) button. • This saves the data. • If the rhythm number where you are saving the data already has data saved to it, a message (Replace?) will appear on the display to confirm whether you want to replace the existing data with the new data. Press the R-14 (YES) button to replace the existing data with the new data or the R-14 (NO) button to cancel and return to the screen in step 9. • The message “Please Wait” will remain on the display while a data save operation is in progress. Do not perform any other operation while it is displayed. Turning off the Digital Keyboard or removing the memory card can cause Digital Keyboard data to be deleted or become corrupted. It also can cause the Digital Keyboard to fail to turn on when the L-1 (POWER) button is pressed. If this happens, refer to “Troubleshooting” (page E-114). • Pressing the R-15 (EXIT) button in place of step 8 displays the confirmation screen shown below. Pressing the R-14 (YES) button at this time will display the user rhythm save screen in step 9. To cancel the editor operation without saving the edited results, press the R-14 (NO) button. • If the size of the accompaniment pattern or instrument part data is too large to be edited, a memory full message (Memory Full) will appear on the display. If that happens, select a different accompaniment pattern or instrument part for editing. To clear user rhythm data 1. Press the C-2 (RHYTHM EDITOR) button to display the rhythm editor screen. 2. While holding down the R-13 (FUNCTION) button, press the C-13 (MENU) button. • This displays the rhythm editor menu. 3. Use the R-17 (y) button to move the 0to “Clear” and then press the R-16 (ENTER) button. • This displays a screen for specifying the number of the rhythm you want to clear. 4. Use the dial or R-14 (–, +) buttons to specify the number of the user rhythm you want to clear. 5. Press the R-16 (ENTER) button. 6. In response to the “Sure?” message that appears, press the R-14 (YES) button to clear or the R-14 (NO) button to cancel. Part Volume/Pan Reverb Send Reverb Chorus Master Volume/Pan Chorus Send Part Volume/Pan Mic In Reverb Send Chorus Send Tone Generator External Input Mono Tone Generator External Input Mono Applying Effects to a Sound You can apply a variety of different acoustic effects to the sounds produced by the Digital Keyboard. The built-in effects include a wide variety of variations that give you access to a selection of general digital effects. • The WK-6500 also lets you apply effects to input from the T-7 (MIC IN) jack. Configuration of Effects The following shows how Digital Keyboard effects are configured. • Items such as “Reverb Send” that are indicated by the symbol are all mixer settings. For details, see “Using the Mixer” (page E-39). • Chorus and DSP cannot be used at the same time. ¦ Chorus Effect Mode Configuration The chorus effect mode is enabled while “Chorus” is selected for the “Chorus/DSP” effect parameter. Chorus and reverb can be used in the chorus effect mode. Part A01-A16, B01-B16 Output Stereo (Area within the broken line is for WK-6500 only.) • For information about “Chorus/DSP”, see “Selecting an Effect” (page E-34). Applying Effects to a Sound Applying Effects to a Sound ¦ DSP Effect Mode Configuration The DSP effect mode is enabled while “DSP” is selected for the “Chorus/DSP”effect parameter. DSP and reverb can be used in the DSP effect mode. Part A01-A16, B01-B16 Output DSP DSP DSP Part Volume/Pan Reverb Send Part Volume/Pan Reverb Send DSP Reverb Send DSP Volume/Pan Mic In Reverb Master Volume/Pan Tone Generator Of...