Оценок - 2, средний балл: 3 ( )

Производитель: Hisense Group Размер: 211.31 kb Название файла: Язык инструкции:

The time can be set for one to twelve hours, in one hour steps. 1 — 2 Press the timer SET button (which advances the time displayed). The display changes immediately to its status previous to timer setting, but the ioN0] indication remains. • To check the status of the timer while it is counting down, press the timer SET button . Cancellation procedure: Press the CANCEL button once again. C STEP 1 STEP 1 STEP 2 2.TIMER OFF mode (Example) C It 1HR 0 0 HIGH POWER O 'S' ON© OFF © CD CD SET CANCEL CD CD FAN SPEED CD CD baseryQac SENSOR OaCL After the length of time set for TIMER OFF elapses, the unit stops operating. The display depicted at left indicates that the air conditioner will stop operating in five hours. Setting Procedure: STEP 1 STEP 2 Press the timer OFF button to set the time at which you want operation to stop. The time can be set for one to twelve hours, in one hour steps. 1 2 12 Press the timer SET button (which advances the time displayed). The display changes immediately to its status previous to timer setting, but the |off01 indication remains. • To check the status of the timer while it is counting down, press the timer SET button . Cancellation procedure: Press the CANCEL button once again. C •13- Using the 1-Hour OFF Timer This function causes the unit to operate for one hour and then stop, regardless of whether the unit is on or off when this button is pressed. The indicator in the display indicates that this function is operating. Setting procedure: Regardless of whether the unit is operating or stopped, press the 1 HR .TIMER button. iHQURgjl Appears in the display. Cancellation procedure: Press the ON/OFF operation button to turn the unit off, wait for the unit to stop operating, and then press the ON/OFFoperation button again. The 1-Hour Timer function is now cancelled and the unit operates normally. NOTE • If, while the 1-Hour Timer function is operating, the 1 HR.TIMER button is pressed once to cancel the function and then again, the unit continues to operate for one hour from that point in time and then stops. • If the 1 HR.TIMER button is pressed while the TIMER OFF function operates,the OFF Timer is cancelled and the unit will stop operating one hour later. qn -IU pHÖUR©]^^^^ (AuTO ■" ^ (A3: N 1HR© ON/OFF “H0 HIGH POWER O TEMP "S' FLAP MODE C ) ON© OFF© FAN SPEED CD CD CD SET CANCEL SLEEP CD CD CD BATTERY O A/C SENSOR OACL C HIGH POWER Operation This operation makes higher or lower temperature airflow than usual, in winter or >, summer, which makes you feel comfortanble as soon as you go home. op -IU 1HR© ON/OFF TEMP O r-^ fS HIGH POWER -o ON© OFF © CD CD SET CANCEL CD CD FAN SPEED CD CD "Í^Oa/c sensor Oacl Setting procedure: Press the High Efficiency button on the remote control unit gently, with a whisper, and the lamp on the display panel is lighted, so the high efficient operation comes to work. It may last the longest time of 15 minutes. | POWER | TIMER ft OPERATING .HIGH POWER lamp ON/OFF button Cancellation procedures: Press the HIGH POWER button again, with a second whisper, the lamp is out. C ON/OFF •14- Special Remarks Heating ( ^ ) Operation Heating performance Defrosting POWER lamp Power failure during operation Clicking Sound Clicking sound is heard from the air conditioner Because this air conditioner heats a room by drawing on the heat of the outside air (heat pump system), the heating efficiency will fall off when the outdoor temperature is very low. If sufficient heat cannot be obtained with this air conditioner, use another heating appliance in conjunction with it. When the outdoor temperature is low, frost or ice may from in the heat exchanger coil, reducing heating performance. When this happens, a microcomputer defrosting system will operate. At the same time the fan on the indoor unit stops ( or runs at very low speed in some cases). Heating operation restarts after several minutes. (This interval will vary slightly depending upon the outdoor temperature and the way in which frost forms). For several minutes after the start of heating operation, the indoor fan will not start running until the indoor heat exchanger coil has warmed up sufficiently. This is because the COLD DRAFT PREVENTION SYSTEM is operating. • The POWER lamp also remains lit during defrosting or when the compressor has been turned off by the thermostat when the system is in the heating mode. In the event of power failure, the unit will stop. When the power is resumed, the unit will restart automatically after three minutes. In heating or cooling operation. Some plastic parts may expand of shrink due to a sudden temperature change. In this event, a clicking sound may occur. This is normal, and the sound will soon disappear. The remote control unit sends the temperature signal to the air conditioner regularly at three-minute intervals. If the signal from the remote control ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: