Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
ew c v NOTES: The needle threader works well with the threads #50-90 and needles #11-16, the blue tipped needle as well. If the needle stops too low to use the needle threaderafter the automatic thread cutting, raise the needle toits highest position by turning the handwheel. 11 qwqzxwqwqzxw Drawing up the Bobbin Thread z Raise the presser foot lifter. Hold the needlethread with your finger. q Needle thread w Bobbin thread x Turn the handwheel one complete turn towardyou. Draw the needle thread to bring up a loop ofthe bobbin thread. er cc Pass the needle thread through the hole in theembroidery foot and draw it up to the threadholder leaving an inch of free thread. e Hole r Thread holder 12 Adjusting the Thread Tension Balanced thread tension: Small amount of the needle thread shows on the wrongside of the fabric. q When the needle thread tension is too tight: The bobbin thread shows on the right side of the fabric. Reduce the tension by turning the tension dial to alower number. q Bobbin thread When the needle tension is too loose: The needle thread forms loops and the stitches look shaggy. Increase the tension by turning the dial to a higher number. 13 Changing Needle Turn off the power switch. Raise the needle by turning qwq the handwheel and lower the presser foot. Loosen the needle clamp screw by turning it counterclockwise. Remove the needle from the clamp. Insert a new needle into the needle clamp with the flatside of the needle to the rear. q Needle clamp screw w Flat side of the needle When inserting the needle into the needle clamp, pushit up as far as it will go and tighten the needle clampscrew firmly. e To check needle straightness, place the flat side of theneedle onto something flat (a needle plate, glass etc.) The gap between the needle and the flat surface shouldbe consistent. e Gap Never use a blunt needle. NOTES: Use the size 11 Blue Tipped Needles for fine fabrics. For medium to heavy weight fabrics, use the size 14needles. 14 (A) e qwr e (B) qw r r w y t e q y q Embroidery Hoops (A) Embroidery Hoop A: This is the standard size hoop, with a 12.6 cm (5”) by11 cm (4 3/8”) embroidery area for sewing PC Cardembroidery designs etc. (B) Embroidery Hoop B: This is the large-size hoop, with a 20 cm (8”) by 14 cm(5 1/2”) embroidery area for sewing large-size designsand combined designs. q Outer hoop w Inner hoop e Attaching knob r Hoop tightening screw Templates When positioning the fabric into the hoop, use thetemplate to align the centerlines on the fabric with thecenter of the hoop. First mark the centerlines on thefabric and place the fabric on the outer hoop. Place theinner hoop and template over the fabric and adjust thefabric placement. q Starting point for built-in and PC Card designs w Starting point for monogramming in horizontalplacement e Starting point for Memory Card No. 102 andup for Memory Craft 5700/9000. r Starting point for monogramming in verticalplacement t Embroidery boundary for built-in and PC Carddesigns. NOTE: The four indentations on the template do notcorrespond with reference lines. y Indentations for positioning the template 15 Adhesive (Iron-on) Stabilizer Place the Wrong side of fabric and the glossy side ofthe stabilizer together. Fold up a corner of thestabilizer and fuse it with an iron. NOTES: Fold up a corner of the stabilizer, to make it easierto peel off the excess stabilizer after stitching. Ironing temperatures vary depending on kind ofadhesive type stabilizer. StabilizerS To obtain the best quality embroidery, it is important touse stabilizers. Types of stabilizer Tear-away Stabilizer is made from a fiber that will teareasily. Use tear-away stabilizers for stable wovenfabrics. After stitching, tear away the stabilizer so thatthe small portion left in the back of the stitching will notaffect the wear. Iron-on Stabilizer is an adhesive type stabilizer for knitsand all kinds of unstable fabrics. Fuse it to the wrongside of the fabrics with an iron. Cut-away Stabilizer is a non-woven fabric that does nottear. Cut the excess portion after stitching. Use cutawaystabilizers for knits and all kinds of unstable fabrics. Water Soluble Stabilizer will dissolve in water. Use this stabilizer for cutwork or lace embroidery, and also forthe right side of looped fabrics such as towel to avoidloops coming through the embroidery. Sticky Stabilizer is a sticky paper used for securing asmall fabric or work that cannot be secured in the hoop. It is also used for velvet and other napped fabric thatwould be permanently marked by the hoop. Usage: The stabilizer should be attached to the wrong sideof fabric. More than one layer may be required. Felt or stable fabrics do not need to be stabilized and you may embroider directly on it. For firm fabrics, you may place a thin paper underthe fabric. The non-adhesive type should be used whenembroidering fabric, which cannot be ironed or forsections, which are difficult to iron. Cut the stabilizer larger than the embroidery hoopand set ...
Эта инструкция также подходит к моделям:Швейные машинки - 350E (3.73 mb)