Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
ONLY) Avant d’utiliser cet appareil, Veuillez lire toutes les instructions. Service a la clientele : 1-800-327-8508 OU INFO@AURORACORP.COM (ETATS-UNIS SEULEMENT) Antes de operar esta unida, por favor lea todas las instrucciones. Servicio al Consumidor: 1-800-327-8508 O INFO@AURORACORP.COM (LOS ESTADOS UNIDOS SOLO) 1 Operating Instructions Installation Operation Caution Trouble Shooting Aurora Paper Shredders Maintenance Limited Warranty Sheet Capacity Credit Card & CD Capacity 1 at a time 15 sheets of 20lb. bond paper Voltage 120V-60Hz 6.5A Paper Shred Size 0.08” x 0.39” pieces 2 mm x 10 mm pieces Installation Fonctionnement Avertissement Depannage des dechiquteuses a papier Aurora Entretien Garantie limitee Manuel de fonctionnement Capacite de passage a la fois 15 feuilles de papier bond de 75g/m2 (20lb.) Capacite de CD et les cartes de credit les introduire un par un Tension 120V-60Hz 6.5A Dimensions des dechets en morceaux de 0.08” x 0.39” en morceaux de 2 mm x 10 mm Instalaciones Operacion Avertencia Solucionar Problemas de la Maquina Trituradora de Documentos Aurora Mantenimiento Garantia Limitada Instrucciones para operar Capacidad de destrucciona la vez 15 hojas de papel de cartes de 20 libras Capacidad de CDs y tarjetas de credito introduzcalos en la ranura uno por uno Voltaje 120V-60Hz 6.5A Tomano de corte en pedazos de 0.08” x 0.39” en pedazos de 2 mm x 10 mm continued on next page Carefully unpack shredder and connect the power cord to any standard 120 volt AC outlet (FIGURE 1). Pull open the shredder door and slide in the wastebasket. After installation, make sure the shredder door is properly closed shut. This shredder features a safety power cut off and will not operate if door is open. Shredders with pull-out wastebaskets feature a safety power cut off upon bin removal (FIGURE 2). Caution: MicroShred shredders have very sharp, exposed blades on the underside. INSTALLATION: OPERATION: REV: In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters of paper that has not passed through. Never attempt to clear a jam by using the reverse function until you have emptied the wastebasket (FIGURE 3). FW: The forward setting can also be used to help clear the cutters in the event of a paper jam. This allows to manually activate the shredder into cutting mode (FIGURE 3). Never shred plastic (except credit cards and only by inserting them, one at a time, through the special credit card slot), continuous forms, anything with adhesive including labels and envelopes, newsprint, or any hard materials. While this shredder will shred staples and small paperclips, it is recommended that you remove them whenever possible in order to extend the life of your shredder. 2 FIGURE 2 FIGURE 3 FIGURE 4 FIGURE 1 POWER: Using the power button or switch, turn on the shredder (FIGURE 4). The green light will indicate whether if the shredder is powered on. This button turns off all features of the shredder. For safety reasons, we recommend that you leave the shredder in the Off position whenever the shredder is unattended or not in use. I Power On O Power Off OPERATION continued: CAUTION continued: 3 4 Features a CD/DVD destroyer: 1) Hold the CD/DVD by the edge and feed one at a time, releasing when shredding begins. 2) Shredder will stop when the entire disc has been destroyed. The shredder does not work at all. a) Make sure the shredder is plugged into an outlet which is in good working order. b) Shredders with pull-out wastebaskets features a safety power cut off upon bin removal. Make sure the pull-out wastebasket is properly set back into place. c) In the event that the shredder is run continuously for too long and the motor overheats, a thermal overload switch will automatically shut the power off. If this happens, move the switch to the off position for 30 minutes or more before continuing. The shredder only runs in "Rev" and "Fw" mode. a) The shredder will not start running until paper, CD/DVD, or credit card is inserted into the appropriate feed slot. It is normal for the motor to run for a moment after the shredder is powered on but it should stop until paper is inserted. The trigger that activates the shredder is located directly in the center of the feed slot. If the paper you are inserting is narrow, it may not be hitting the switch. It is possible that the trigger, which activates the shredder, has become blocked with paper. Insert an index card, directly in the center of the feed slot, and apply force. This will usually clear any paper blocking the switch and force the switch closed. TROUBLE SHOOTING FOR AURORA PAPER SHREDDERS: CAUTION: MAINTENANCE: We recommend you oil your shredder once a month with vegetable or cooking oil (nothing petroleum based). Drizzle some oil on a few pieces of paper and feed those pages through the shredder. Do not spray or keep any aersol products in or around shredder CAUTION: Do not hold CD/DVD with finger through the center ring while feeding...