Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Be sure to tighten the screw securely. To remove wheel guard, follow the installation procedure in reverse. 1 2 3 1. Lock nut 2. Depressed center grinding wheel/ Multi-disc 3. Inner flange 001074 Installing or removing depressed center grinding wheel/Multi-disc WARNING: • Always use supplied guard when depressed center grinding wheel/Multi-d

6. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. Run the tool (with guard) at no load for about a minute, holding tool away from others. If wheel is flawed, it will likely separate during this test. 7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 9. NEVER use tool with wood cutt

Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. 21. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used

Used Description Item No. Part No. No. Used Description 1 416449-8 1 Pin Cap 39 442126-6 1 Gasket 2 233089-5 1 Compression Spring 12 40 211236-8 1 Ball Bearing 6002DDW 3 266173-1 Tapping Screw 5X30 41 962151-6 1 Retaining Ring R-32 4 * 1 Gear Housing Com. 42 324077-4 1 Lock Sleeve 5 941152-7 1 Flat Washer 6 43 233905-1 1 Lock Spring 17 44 267757-8 1 Lock Washer 6 226755-1 1 Spiral Bevel Gear 12 183317-7 1 Spiral Bevel Gear Set 45 227404-3 Spiral Bevel Gear 33 (Includes Ite

Used Description Item No. Part No. No. Used Description 1 416449-8 1 Pin Cap Accessories 2 233089-5 1 Compression Spring 12 3 266173-1 4 Tapping Screw Flange PT5x30 4 * 1 Gear Housing Com. (Includes Needle A01 126097-9 1 Wheel Cover Assy (9015B) Bearing 810 - 212043-2) (Items 1, (Includes Item 33) 2 & 40 - NOT INCLUDED) 134961-3 1 Wheel Cover Assy (9016B) (Includes Item 33) (Old 165213-1 - Item 33 5 961003-8 1 Retaining Ring S-7 NOT INCLUDED) 6 * 1 Spiral

Disc) 38 * 1 Spiral Bevel Gear 33 (9015B) A08 1 Abrasive Disc 226754-3 1 Spiral Bevel Gear 35 (9016B*) (See Catalogue for Details) A09 224517-1 1 Lock Nut 5/8-48 (For Abrasive Disc) 40 256446-0 1 Pin 6 A10 1 Wire Cup Brush (5/8"-11 Arbor) 100 664208-4 2 Receptacle (Old 654098-5) (See Catalogue for Details) 101 654551-1 2 Connector A11 152492-0 1 Grip 36 Com. A12 782412-6 1 Lock Nut Wirench 28-185 A13 1 Diamond Cutter (See Catalogue for Details) A14 1 M

It's safer than using your hand and it frees both hands to operate tool. 11. DON'T OVERREACH. Keep proper footing and balance at all times. 12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and charging accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Keep handles dry, clean, and free from oil and grease. 13. DISCONNECT TOOLS. When not in use, before servicing, a

If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Hold the tool firmly with both hands. 2. Make sure the belt is not contacting the workpiece before the switch is turned on. 3.Keep hands away from rotating parts. 4. Do not leave the tool running. Operate the tool only when hand-held. 5. This tool has not been waterproofed, so do not use water on the workpiece surface. SAVE THESE INSTRUCTIONS.

Adjusting arm inclination The arm can be pivoted and fixed at any desired angle within the "A" range according to the operating position or the figure of the workpiece. Loosen the lock lever by raising it. Pivot the arm to the desired position, and secure the lock lever to fix the arm firmly. Replacing arm By replacing the standard-equipped arm by optional one, 6 mm (1/4") or 13 mm (1/2") width belt can be used. Remove the arm by loosening the screw that secures the arm. Insert thearm that fits

Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Hold the tool firmly with both hands. 2. Do not leave the tool running. Operate the tool only when hand-held. 3.This tool has not been waterproofed, so do not use water on the working surface. SAVE THESE INSTRUCTIONS. Attaching the abrasive paper Pull out the clamp lever and insert the paper end. Be careful to maintain the proper paper tension. Align edges of paper with either edg