To adjust the angle, slightly loosen the Lock Screw (15). (See Figure H.) 4. Observe the gauge on the Angle Plate (14). Raise or lower the Work Table (13) to set the Work Table to the desired angle. Then, retighten the Lock Screw (15) to lock the Work Table in place. (See Figure H.) SKU 05154 PAGE 12 FIGURE H LOCK SCREW (15) WORK TABLE (13) ANGLE PLATE (14) To AdjustThe Angle OfThe Miter Guide: 1. The angle of the Miter Guide (21) may be adjusted to the right 0 to 45 degrees and to the left 0 to

/ Camarillo, CA 93011 Copyright © 1996 by Central Purchasing Incorporated. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Central Purchasing Incorporated. For technical questions and replacement parts, please call 1-800-444-3353. CHICAGO HEHIlHPowTToobl INDUSTRIAL SPECIFICATIONS Item # 31309 I AmpsA/olts I 5.5 Amps /120 VAC [ Power 660 Watts I No load speed 10000 RPM Weight 6-

SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Grinder. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Always grip the Grinder firmly when operating the tool. 3. Always use accessories that have an RPM rating of at least 21,000 and a 1/4” diameter shank. Using accessories not rated to meet the RPM capacity of this tool or with an improperly sized shank can result in damaged accessories, personal injury, and/or prope

Step3: On the top of the WATER TRAP is an arrow. Attach the BRASS AIR SUPPLY VALVE to the NIPPLE CONNECTOR that the arrow is facing away from. Step4: Attach the MALE/FEMALE ADAPTER to the BRASS AIR SUPPLY VALVE. Page #6 -- SKU 34202 Sand Control Valve Refer to Figure 3. Step1: Get out the TANK (#1), the SAND CONTROL VALVE (#18B), two NIPPLE CONNECTORS (#16), and the SAND OUTLET MANIFOLD (#22). Nipple Connector (#16) Sand Control CONNECTORS to the bottom of the (#1) Step2: Attach one of the NIPPL

Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 or 240 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 1

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS SKU 36572 For technical questions, please call 1-800-444-3353 PAGE 2 WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate pneumatic tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pneumatic tools create sparks which may ignite flammables. 3. Keep bystanders, children, and visitors away while operating a pneumatic tool. Distractio

Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. 12. DON’T OVERREACH. Keep proper footing and balance at all times. 13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 14. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like. 15. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position bef

An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. 10. WEAR PROPER APPAREL. Do not wear loose clothing, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hai

This feature helps prevent unauthorized use of the Sander. (See Figure L.) 2. Insert the Switch Key (21) into the ON/OFF Locking Switch (22). (See Figure L.) 3. To turn the Sander on, place your finger under the left side of the ON/OFF Locking Switch (22) and pull out. (See Figure L.) 4. To turn the Sander off, push in on the left side of the ON/OFF Locking Switch (22). (See Figure K.) 5. To lock the ON/OFF Locking Switch (22) in its OFF position, push and hold the left side of the Switch while

If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. 3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between different processes. 5. Include vibration-free periods each