Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided. • Use safety apparel and equipment. Use safety goggles or safety glasses with side shields which comply with current national standards, or when needed, a face shield. Use as dust mask in dusty work conditions. This applies to all persons in the work area. Also use non-skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate. • Avoid accidental starting. Ensure the switch is in the off position before plugging tool into power outlet. In the event of a power failure, while a tool is being used, turn the switch off to prevent surprise starting when power is restored. • Do not overreach. Keep proper footing and balance at all times. • Remove adjusting keys or wrenches before connecting to the power supply or turning on the tool. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. TOOL USE AND CARE • Do not force the tool. Tools do a better and safer job when used in the manner for which they are designed. Plan your work, and use the correct tool for the job. • Never use a tool with a malfunctioning switch. Any power tool that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using. • Disconnect power from tool and place the switch in the locked or off position before servicing, adjusting, installing accessories or attachments, or storing. Such preventive safety measures reduce the risk of starting the power tool accidentally. • Secure work with clamps or a vise instead of your hand to hold work when practical. This safety precaution allows for proper tool operation using both hands. • Store idle tools. When tools are not is use, store them in a dry, secure place out of the reach of children. Inspect tools for good working condition prior to storage and before re-use. 3 • Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. • Keep guards in place and in working order. • Never leave tool running unattended. UNPACKING When unpacking the Bench Grinder, please check if any parts are missing or broken, please call Northern Tool + Equipment. Carefully remove the grinder and related hardware from the carton and examine it thoroughly to insure it has not been damaged. This carton should contain the following items: Description Qty Bench Grinder . . . . . . . . . . . . . . . .1 Eye Shields . . . . . . . . . . . . . . . . . .2 Tool Restst . . . . . . . . . . . . . . . . . . .2 Spark Guards . . . . . . . . . . . . . . . . .2 Manual . . . . . . . . . . . . . . . . . . . . . .1 Short bolts . . . . . . . . . . . . . . . . . . .4 Bolts . . . . . . . . . . . . . . . . . . . . . . . .2 Long bolts . . . . . . . . . . . . . . . . . . .2 Mounting Rods . . . . . . . . . . . . . . . .2 Washers . . . . . . . . . . . . . . . . . . . . .2 Brackets . . . . . . . . . . . . . . . . . . . . .2 Large Washers . . . . . . . . . . . . . . . .6 4 ASSEMBLY SWITCH The switch is located on the front of the grinder near the bottom. To turn the tool ON depress the rocker switch at the top near the word ON. To turn the tool OFF depress the bottom por- tion of the rocker switch near the word OFF. INSTALLING TOOL RESTS Turn off and unplug the bench grinder. Remove the tool rests from the top portion of the poly-foam carton liner and install them to the wheel guards as shown in the figure. Use the bolts and washers from the plastic bag to secure them in place as shown in Figure 1. NOTE: There is a left and a right tool rest. Refer to Figure 1 to ensure that you install them correctly. When in actual use, the tool rests should be adjusted to within 1/4" of the grind- ing wheel or other accessory being used. INSTALLING THE SPARK GUARDS AND EYE SHIELD BRACKETS Turn off and unplug the bench grinder. The spark guards are packed in the plastic bag shipped with your grinder. Select from the bag, the two spark guards and the two smaller bolts and washers. Install the spark guards to the wheel guards of your grinder as shown in Figure 2. Adjust them to within 1/16" of the grinding wheel or other accessory being used. NOTE: There is a left and right spark guard. Refer to Figure 2 to ensure, that you install them correctly. INSTALLING THE EYE SHIELDS Turn off and unplug the bench grinder. Remove all remaining parts from the plastic bag. NOTE: There is a left and a right eye shield mounting rod. Examine the figure closely to ensure that you are installing them correctly. The one pictured in Figure 3 is for the right wheel guard as you face the front of the tool. Carefully examine Figure 3 and assemble one rod, one bracket, one bolt and one flat w...