Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Such preventive safety measures reduce the risk of starting the power tool accidentally. d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 6. Electrical safety Your tool is double insulated; therefore no earth wire is required. Always check that the main voltage corresponds to the voltage on the rating plate. Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized Black & Decker Service Center or an equally qualified person in order to avoid damage or injury. If the power cord is replaced by an equally qualified person, but not authorized by Black & Decker, the warranty will not be valid. 7. Labels on Tool The label on your tool may include the following symbols: V ........... Volts ........ Direct Current Read Instructions Manual A ........... Amperes n0.......... No-Load Speed Hz ......... Hertz ........ Class II Construction Use Eye Protection W........... Watts ........ Earthing Terminal min........ minutes ........ Safety Alert Symbol Use Ear Protection ........ Alternating Current .../min.... Revolutions or Reciprocation per minute AADDDDIITTIIOONNAALLSSAAFFEETTYYIINNSSTTRRUUCCTTIIOONNSSFFOORRSSMMAALLLLAANNGGLLEEGGRRIINNDDEERRSS • Use the guard and ensure it is fitted correctly. • Check mounting flanges and the disc are correctly fitted and are undamaged. • Ensure you are using the correct size and type of disc for the task. • Ensure the disc, wire brush and sanding accessories are rated in excess of the spindle rpm of your angle grinder. Allow a newly assembled wheel to idle off-load for 30 seconds before starting any operation. FEATURES (FIG. 1) 1. Slider switch 3. Tool free guard 5. Side handle (3 positions) 2. Cable 4. Body grip 6. Spindle lock button OPERATING YOUR ANGLE GRINDER (FIG. 1) To switch on, push the slider switch forward. To switch off, press the rear of the slider switch. FITTING THE DISCS (FIG. 2 & 3) Proceed as follows: • Disconnect the plug from the electricity supply. • Ensure the guard is fitted. Place the inner flange (Fig. 2-A) on the spindle. Ensure it is located on the two flats. • Place the abrasive disc on the spindle and inner flange (Fig 2-B). Ensure it is correctly located. • Fit the threaded outer flange (Fig. 2-C), making sure it is facing in the correct direction for the type of disc fitted. For grinding discs, the flange (Fig. 2-C) is fitted with the raised portion facing towards the disc. For cutting discs, the flange (Fig. 2-C) is fitted with the inner portion facing away from the disc. • Hold the spanner on the flats of the spindle to prevent rotation of the disc and tighten the outer flange with the spanner provided. 13 ENGLISH • Press in the spindle lock button and rotate the spindle until it locks (Fig. 3). Keeping the lock button pressed in, tighten the outer flange with the spanner provided. FITTING SANDING DISCS (FIG. 4) • Use a sanding disc with the backing pad for sanding with your angle grinder. • Disconnect the plug from the electricity supply. • Remove the guard. • Place the flange on the spindle. Place the backing pad on the spindle and inner flange, ensuring it is correctly located. • Mount the fibre backed abrasive disc on the backing pad. • Fit the threaded outer flange and tighten as explained in "Fitting the discs". HANDY HINTS (FIG. 5) Hold your angle grinder firmly with one hand around the side handle and the other around the body of your angle grinder. • Always position the guard so that as much of the exposed disc as possible is pointing away from you. • Be prepared for a stream of sparks when the disc touches the metal. When grinding, always maintain the correct angle between the disc and the work surface (15°) (Fig. 5). This increases the removal capacity of the disc and avoids unnecessary overloading. OVERLOAD Overloading will cause damage to the motor of your angle grinder. This can happen if your angle grinder is subjected to heavy duty use for prolonged periods of use. Do not in any circumstances, attempt to exert too much pressure on your angle grinder to speed up your work. The abrasive discs operate more efficiently when a...