Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
PRINTED IN TAIWAN TECHNICAL DATA ] Model.........................................................................................................G9248 Dimension (LengthX WidthX Height)..................229.6(9”)x 58(2.3”)x240(9.4”)mm Weight..........................................................................................1.45kgs (3.19bs) Air inlet..........................................................................................□ NPT 1/4” □ PT 1/4” Compressed air: Maximum permissible operating pressure..........................................llOpsi (7.8bar) Recommended operating pressure....................................60 ~ lOOpsi (4.1 ~ 6.9 bar) Fastener range..............................18 Ga. Staples 8 ~ 40mm (5/16” ~ 1 9/16”) 18 Ga. Brad nails 15 ~ 50mm (5/8” ~ 2”) Nail/Staple capacity.......................................................................................lOOpcs NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH Enxxl: A-weighted single-event sound pressure level at operator’s position: LpA^s=92dBA A-weighted single sound pressure level: LpA ls lm=87dBA VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH IS08662; PART II: Weighted root mean square acceleration = 1.5m/s2 (* AT WORKPLACE, ALWAYS WEAR HEARING PROTECTION EQUIPMENT*) 1 NOTE 1. To Load Nails 1-1. Press the rear latch to slide out the magazine cover. 1 -2. Hold the tool horizontally. 1-3. Attach brads to the nail guide (brad slot) on the inner top of the magazine. Ensure brad heads are attached to it. BRAD SLOT. 2. To Load Staples 2-1. See 1-1. 2-2. Hold the tool horizontally. Insert staples and attach them to the inner top of the magazine. 2 2-3.Ensure staples are attached to the inner top of the magazine. See the diagram below. Special Features: A. Firing Mode 1. Single Shot/Sequential Shot A unique design to meet both demands for fine finish nailing & high speed stapling. 2. Switch clockwise for sequential-shot mode. 3. Switch counterclockwise for single-shot mode. B. Depth-of-drive Adjustment 2. Innovative driver blade system & depth-of-drive adjustment ensure no countersink marking for extra fine nailing operation. Rotate finger wheel to adjust depth of drive. 3.Kit complete with: 1 .Oiler 2.Safety Goggle 3.Allen Wrenches 4.Compact Carrying Case 5.Nails Assortment :1 '/4”xl,000pcs 2”xl,000pcs 6. Staples Assortment :l”x400pcs 1 '/4”x400pcs 3 WARNING A Depicts a potentially hazardous situation that, if not avoided, could result in death or serious injury. DANGER A) Depicts an imminently hazardous situation that, if not avoided, could result in death or serious injury. NOTE Emphasizes useful information. 4 SAFETY INSTRUCTIONS | DANGER A] Do not attempt to operate the tool until you read and understand all safety precautions d manual instructions. Never allow to use oxygen or combustible gas as a power source for the tool. Use filtered, lubricated, regulated compressed air only. Never use gasoline or other flammable liquids to clean the tool. Vapors in the tool will ignite by a spark and cause the tool to explode. Do not exceed maximum permissible operating pressure 7.8bar(115psi). i Any tool equipped with contact actuation with a safety yoke shall not be used 5 - if changing one driving location to antother involves the use of stairs, ladders or scaffolding. -for closing boxes or crates and for fitting transportation safety systems. 0 Disconnect the tool from air supply before clearing jams,performing repairs and during non-operation WARNING^ # Do not keep the trigger pulled on safety yoke mechanism when carrying or holding the tool. Never carry the tool by the hose or pull the hose to move the tool. Carry the tool only by the handle. # At the workplace, always wear the protective equipment such as Z87.1 safety glasses, ear and head protection. # Do not use a check valve or any other fitting that allows air to remain in the tool. # Never point any operational fastener driving tool at yourself or at anyother person. 6 COMPRESSED AIR SYSTEM NOTE NOTE NOTE # Many air tool users find it convenient to i oiler to help provide oil circulation throu; tool and increase the efficiency and usefi life of the tool. Check oil level in the oil« daily. Many air tool user find it convenii to use a filter to remove liquid and impurities which can rust or wear interna parts of the tool. A filter also increase th efficiency and useful of the tool. The filt must be checked on a daily basis and if necessary drained. # When the air pressure in the line system exceeds the maximum permissible operai pressure of the tool, a pressure reducing' valve followed by a downstream safety valve must additionally be fitted in the supply line to the tool, # Compressed air pipelines should be laid s as to form a gradient (highest point in the direction to the compressor). Easily accessible water separators should be installed at the lowest points. # Junctions for opera...