Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
It is important to keep moving the object back and forth across the grinding wheel and to cool the object frequently using the grinder’s Coolant Tray. AUTO-ON WORKLIGHT SHIELD RODS (RIGHT AND LEFT) SPARK DEFLECTOR (RIGHT) WHEEL GUARD WORK REST (RIGHT) ON SPARK DEFLECTOR (LEFT) OFF SAFETY SHIELD(S) WORK REST (LEFT) COOLANT TRAY SWITCH MODEL BGH825 Fig. 3c ASSEMBLY WARNING: Always disconnect the bench grinder from the power source before performing any assembly or adjustment. Failure to do so could result in accidental starting resulting in possible serious personal injury. SPARK DEFLECTOR – BGH615 See Figure 4a. Using two 6 mm hex bolts and washers, attach the spark deflector to the inside of the wheel guard. Adjust the spark deflectors to within 1/16 in. of the grinding wheel. Tighten the hex bolts securely. SPARK DEFLECTOR – BGH625 AND BGH825 See Figures 4b and 4c. Using the two phillips head screws, washers, and lock washers, attach the spark deflector to the top of the wheel guard. Adjust the spark deflectors to within 1/16 in. of the grinding wheel. Tighten the hex bolts securely. WARNING: Always spin the wheel by hand before turning on the grinder to make sure the spark deflector doesn’t hit the grinding wheel. WARNING: Always make sure your bench grinder is securely mounted to a workbench or an approved workstand. Failure to do so could result in an accident resulting in possible serious personal injury. WASHER HEX BOLT SPARK DEFLECTOR Fig. 4a BGH615 SPARK DEFLECTOR WASHER SCREW LOCK WASHER Fig. 4b BGH625 SPARK DEFLECTOR WASHER SCREW LOCK WASHER BGH825 Fig. 4c ASSEMBLY SHIELD BRACKET ASSEMBLY See Figure 5. Note: The hardware used for assembling the safety shields to the shield brackets has been preassembled and prepackaged. Remove the two phillips head screws, washers, and hex nuts from the shield bracket. Fit the shield bracket to the top of the safety shield. Reattach the screws, washers, and hex nuts taking care not to tighten the screws so tight as to crack the plastic. Repeat for the other shield bracket and safety shield. SHIELD ROD CLAMP BRACKET WASHER HEX BOLT WARNING: To prevent personal injury, never operate the bench grinder unless the safety shields and spark deflectors are properly installed and in place. Fig. 6a BGH615 MOUNTING SAFETY SHIELDS See Figures 6a - 6c. Mount the left and right shield rods to the inside of the wheel guards using the clamp brackets, hex bolts (8 mm x 14 mm), and washers (8 mm). Locate your grinder in figures 6a, 6b, or 6c. Use the illustration as a guide to determine which shield rod is mounted on the left and which shield rod is mounted on the right of the grinder. Once shield rods are firmly in place, slide the shield bracket onto the shield rod. Tighten the carriage bolt leaving it loose enough to allow the safety shield to be raised and lowered easily. SHIELD ROD CLAMP BRACKET WASHER HEX BOLT PHILLIPS SCREW CARRIAGE BOLT SHIELD ROD Fig. 6b BGH625 SHIELD ROD WASHER CLAMP BRACKET SHIELD BRACKET WASHER HEX BOLT HEX NUT LOCK WASHER WASHER LOCK WASHER SAFETY SHIELD HEX NUT Fig. 5 Fig. 6c BGH825 ASSEMBLY WORK REST – BGH615 See Figure 7a. Mount the work rests to the inside of each wheel guard using two hex bolts (8 mm x 8) and two washers (8 mm) on each side. Before tightening the bolts, adjust the gap between the grinding wheel and the work rest to a maximum of 1/16 in. Tighten securely. WORK REST – BGH625 See Figure 7b. Mount the work rests to the work rest bracket using the knob, washer, and one hex nut. Before tightening the bolts, adjust the gap between the grinding wheel and the work rest to a maximum of 1/16 in. Tighten securely. WORK REST – BGH825 See Figure 7c. Before attempting to mount the work rest, remove the hex nut and star washer from the phillips screw. See Figure 7c. Place the work rest over the phillips screw before replacing the hex nut and star washer. Using the hex bolt (5 mm x 10 mm) and washer (5 mm), secure the work rest against the inside of the wheel guard. Before tightening the bolts, adjust the gap between the grinding wheel and the work rest to a maximum of 1/16 in. Tighten securely. WORK REST WASHERS HEX BOLTS Fig. 7a BGH615 HEX NUT WASHER WORK REST BRACKET WORK REST KNOB BGH625 Fig. 7b PHILLIPS SCREW WORK REST STAR WASHER HEX NUT HEX BOLT WASHER Fig. 7c BGH825 OPERATION BASIC OPERATION WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, wear a dust mask. To be efficient and work as designed, your tools should be kept sharp. Dull tools can and will cause accidents. Bench Grinders are ideal for sharpening tools such as chisels, planer blades, scissors, etc., and for removing rust or corrosion. WARNING: Never sharpen or grind anything made of aluminum. Grinders remove material rapidly so pressure is the key to efficient grinding. The proper way to sharpen a tool and avoid overheating is: nKeep the object in constant motion, moving it at an even ...
Эта инструкция также подходит к моделям:Шлифовальные станки - BGH615 (5.69 mb)
Шлифовальные станки - BGH625 (5.69 mb)