Оценок - 3, средний балл: 4 ( )

Производитель: Northern Industrial Tools Размер: 222.98 kb Название файла: Язык инструкции:

CAUTION: • After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. Grinding and sanding operation ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. During the break-in period with a new wheel, do not work the 1 2 3 1. Lock nut 2. Abrasive disc 3. Rubber pad 002983 A B 10 grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. Operation with wire cup brush (optional accessory) CAUTION: • Check operation of brush by running tool with no load, insuring that no one is in front of or in line with brush. • Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential for injury from contact with broken brush wires. Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire cup brush onto spindle and tighten with supplied wrench. When using brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. Operation with wire wheel brush (optional accessory) CAUTION: • Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. • Do not use wire wheel brush that is damaged, or which is out of balance. Use of damaged wire wheel brush could increase potential for injury from contact with broken wires. • ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury. Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. 1. Wire cup brush 1 001136 1. Wire wheel brush 1 001229 001618 1 4 3 2 001618 1 4 3 2 1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Wheel guard for cut-off wheel MAINTENANCE 002985 1 2 1. Exhaust vent 2. Inhalation vent ACCESSORIES Operation with abrasive cut-off wheel (optional accessory) WARNING: • When using an abrasive cut-off wheel, be sure to use only the special wheel guard designed for use with cutoff wheels. • NEVER use cut-off wheel for side grinding. During cutting operations, never change the angle of the wheel. Placing side pressure on the cut-off wheel (as in grinding) will cause the wheel to crack and break, causing serious personal injury. CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to become obstructed. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc, flex wheel and wire wheel brush. A cut-off wheel can also be used with an optional guard. If you decide to use your Makita grinder with approved accessories which you purchase from your Makita distributor or factory service center, be sure to obtain and use all necessary fasteners and guards as recommended in this manual. Your failure to guards as recommended in this manual. Your failure to 2 3 2 2 11 12 13 4 14 33 6 8 9 10 1 5 7 5 5 9560CV/9563CV 9561CV/9564CV 9565CV 1 Grip 36 2 Wheel guard 3 Inner flange 35 Inner flange 45 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 10-35 Lock nut 5/8-45 6 Plastic pad -N/A 7 Flex wheel -N/A 8 Rubber pad 76 Rubber pad 100 Rubber pad 115 9 Abrasive disc 10 Sanding lock nut 10-30 Sanding lock nut 5/8-48 11 Wire wheel brush 12 Wire cup brush 13 Wheel guard (For cut-off wheel) 14 Cut-off wheel -Lock nut wrench 20 Lock nut wrench 28 Lock nut wrench 28 Cut Cut s Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Su...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: