Войти:
Оценок - 4, средний балл: 4.5 ( )

Инструкция по эксплуатации Campbell Hausfeld, модель PL1551

Производитель: Campbell Hausfeld
Размер: 1.34 mb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


14. Do not put hands near or under moving parts. 15. Always secure workpiece in a vise or clamp. Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. Operation LUbrICaTIOn Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the tool and will void the warranty. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2010 Campbell Hausfeld/Scott Fetzer For parts, product & service information IN241203AV 2/10 visit Operating Instructions Operation (Continued) This air tool requires lubrication before the initial use and before and after each additional use. Air tools require lubrication throughout the life of the tool. Follow the outlined procedures carefully. Campbell Hausfeld air tool oil (ST1270) is recommended because this oil cleans, lubricates and inhibits rust all in one step. aIr mOTOr LUbrICaTIOn The air motor must be lubricated daily. An air motor cannot be oiled too often. Disconnect the air tool from the air supply before lubricating. 1. Disconnect the tool from the air supply. 2. Turn the air tool upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of Campbell Hausfeld oil in the air inlet. After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, the ex-haust port must be covered with a towel before applying air pressure. Failure to cover the exhaust port can result in serious injury. 4. Release the trigger and connect the air tool to the air supply. Cover the exhaust port with a towel then run the air tool for 7 to 10 seconds. Oil will discharge from the exhaust port when air pressure is applied. Continue to run the sander until no oil is discharged. Wipe all residual oil from the tool before use. SPeeD aDjUSTmenT This sander is equipped with a regulator for speed adjustment (See Replacement Parts List for Specifications). aTTaCHInG SanDInG PaD/DUaL aCTIOn SanDerS Adhesive backed discs are recommended. To apply the sandpaper, align outside edge and press self adhesive paper onto the pad. Change sandpaper as needed. Disconnect the air tool from the air supply before attaching the sanding pad. Do not operate the sander if sanding pad is not securely tightened. Always replace a worn or damaged pad. Serious injury could occur. 1. Lock the drive spindle in place before attaching the sanding pad. Rotate the spindle lock until the spindle lock engages with the drive spindle and hand- tighten the sanding pad in a clockwise direction (See Figure 1). Figure 1 Drive Spindle Spindle Lock Operating Postion Pad assembly Postion 2. Unlock the spindle before applying air pressure. nOTe: The spi...

Эта инструкция также подходит к моделям:
Шлифовальные станки - TL1004 (1.34 mb)
Шлифовальные станки - TL1005 (1.34 mb)
Шлифовальные станки - TL1118 (1.34 mb)
Шлифовальные станки - FHT504 (1.34 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории