Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Make sure power is off before plugging in the Sander/ Grinder. 2. Check Sander / Grinder for damaged parts. 3. Make sure all clamps, locks, and bolts are tight. 4. Remove any adjusting keys or wrenches. 5. Make sure guards are in place and in proper working order. Warning! Make sure table is securely locked into place following adjustments. Table should be secured to a flat, level surface capable of supporting weight of the Sander/Grinder as well as workpiece material being used. 6. Give Sander / Grinder a test run. If the tool vibrates irregularly or makes unfamiliar noises, turn it off, unplug it, and refer to an authorized service technician. Work Table Adjustment Figure 1 On / Off Switch Neutral / Direction Switch Work Table Degree Gauge Tilt Lock Height Lock Miter Slot Height Adjustment Wheel Tilt Adjustment Wheel Note: There must be a 1/16” clearance between the Work Table and the face of the Sanding Disc. Refer to Figure 1 above. 1. The angle of the of the work table adjusts between 0 - 30 degrees to the left (standing at rear adjustment), or 0 - 45 degrees to the right. 2. Loosen the Tilt Lock lever and turn the Tilt Adjustment Wheel to the desired direction. Use the Degree Gauge to set precise angles. Tighten the Tilt Lock lever. Page 5 SKU 45725 Operation (continued) Refer to Figure 1 on page 5. 3. To adjust the height of the Work Table, loosen the Height Lock lever and turn the Height Adjustment Wheel to the desired height. Tighten the Height Lock lever. Note: Before operation, make sure you are working in the right direction of feed. The disc will travel in either direction. You must move your workpiece in the opposite direction of the disc. See Figure 2 below. Failure to feed the material in the proper direction will lead to serious personal injury or property damage. Figure 2 Direction of Rotation (left) Direction of Feed (right) Running the Sander / Grinder Note: Your Sander / Grinder has a vacuum port (2-1/2” O.D. with 2-3/16” Adapter) for dust Caution: Keep fingers and hands well clear of the spinning disc and the clearance between the table and the spinning disc. collection. 1. You should always use a miter gauge (not included) to move material through the Sander / Grinder. Miter gauges are available at Harbor Freight Tools. This tool uses a 3/4” miter gauge. Read the instructions that come with the miter gauge for miter settings and adjustments. Always hold the workpiece firmly against the miter gauge and the Table; be aware of the potential for workpiece “kickback”. 2. Plug in the Sander / Grinder. 3. Make sure the Neutral / Direction Switch is in neutral to start. See Figure 1 on page 5 4. Turn the On / Off Switch to On. See Figure 1 on page 5. 5. Determine the direction you want the disc to spin, and flip the Neutral / Direction Switch in that direction. Warning! Make sure you feed material from the opposite direction. Failure to feed the material in the proper direction will lead to serious personal injury or property damage. See Figure 2 above. Page 6 SKU 45725 Operation (continued) 6. When you finish sanding or grinding, turn the Neutral / Direction Switch to neutral and wait until the wheel comes to a complete stop. Turn off the On / Off Switch. See Figure 1. 7. If you wish to switch rotation direction without turning off the machine, turn the Neutral / Direction Switch to neutral and wait until the wheel comes to a complete stop, and then turn switch to the opposite direction. Maintenance Warning! Make sure your Sander / Grinder is unplugged before attempting any maintenance. 1. Remove your vacuum hose (not included) from the vacuum port and clean out port. 2. Clean the surface of the Sander / Grinder with a clean cloth or soft dry brush. 3. Check all nuts and bolts for tightness. Tighten if necessary. 4. Check sanding disk for tears or frays. Replace if necessary. 5. Clean debris from 3/4” miter slot. Page 7 SKU 45725 Parts List Part No. Description Qty. Part No. Description Qty. Part No. Description Qty. 1 Base 1 36 Spring Pin 1 71 Set Screw 4 2 Column 1 37 Worm Gear 1 72 Fixed Washer 8 3 Cover/Support 1 38 Washer 1 73 Motor Base 2 4 Screw 4 39 Fixed Washer 1 74 Washer 4 5 Spring Washer 4 40 Sheave Stand 1 75 Fixed Nut 4 6 Set Washer 4 41 Lock Handle 1 76 Fixed Screw 4 7 Motor Mount 1 42 Knob 1 77 Steel Washer 8 8 Upper Spring Pin 1 43 Rack 1 78 Motor 1 9 Stud Bolt 1 44 Rack Set Screw 2 79 Nut 4 10 Fixed Nut 1 45 Solid Segment 1 80 Cord 1 11 Set Spring Washer 1 46 Table 1 81 Equal Key 1 12 Fixed Washer 1 47 Screw 1 82 Screw 3 13 Spring Stud Bolt 1 48 Fixed Pin 1 83 Fixed Washer 3 14 Stud Washer 1 49 Table Adj. 1 84 Hub 1 15 Bracket 1 50 Table Screw 1 85 Disc 1 16 Spring 2 51 Table Washer 1 86 Clamp Block 1 17 Keeper 2 52 Pilot 1 87 Clamp Screw 1 18 Sheave 2 53 Pilot Screw 4 88 Sanding Cloth 1 19 Fixed Screw 1 54 Spring Pin 1 89 Disc Guard 1 20 Fixed Washer 2 55 Pilot 1 90 Left Arm Guard 1 21 Fixed Nut 1 56 Gear Segment 1 91 Right Arm Guard 1 22 Pin 1 57 Scale Set Knob 1 92 Guard...