Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
This angle grinder is supplied with a lock-off lever to prevent accidental starts. To begin operation, grip tool and depress the safety lock with thumb then depress throttle lever. CAUTION: NEVER OPERATE TOOL WITHOUT GUARD PROPERLY INSTALLED. DO NOT OVERTIGHTEN WHEEL NUT OR WHEEL MAY CRACK. Maintenance LUBRICATION: An automatic in-line filter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with John Deere AT-4003 air tool oil. Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator is properly set when a light stain of oil collects on the paper. Excessive amounts of oil should be avoided. In the event that it becomes necessary to store the tool for an extended period of time (overnight, weekend, etc.), it should receive a generous amount of lubrication at that time. The tool should be run for approximately 30 seconds to ensure oil has been evenly distributed throughout the tool. The tool should be stored in a clean and dry environment. Recommended lubricants: Use John Deere AT-4003 air tool oil or any other high grade turbine oil containing moisture absorbent, rust inhibitors, metal wetting agents and an EP (extreme pressure) additive. 4-Inch Angle Grinder Operator's Manual TroubleshooTroubleshooSymptom Problem Solution Loss of Power 1. Low air pressure 2. Improper lubrication or dirt build up 3. Worn motor parts, or other problems 1. Check air supply. For rated performance, 90 PSI air pressure is required at the tool, with tool operating 2. Check for wet or dirty air. Wet air tends to wash lubricant away. Dirt or foreign matter will impede the action of the motor. If dirt or water has entered the tool, flush with John Deere AT-4003. 3. Contact your customer service. Specifications Wheel capacity -------------------------------4" Type 27 Wheel size --------------------------------------4" X 1/4" X 5/8" Spindle size -------------------------------------3/8"- 24 Free speed --------------------------------------11,000 RPM Power output ----------------------------------3/ 4 HP Weight -------------------------------------------4 lbs. Length --------------------------------------------9" Average air consumption ------------------5 CFM Recommended hose size -------------------3/8" I.D. Air inlet -------------------------------------------1/4" NPT Maximum air pressure -----------------------90 PSI 4-Inch Angle Grinder Operator's Manual Limited Warranty Limited Warranty Limitation of Liability. To the extent allowable under applicable law, John Deere’s liability for consequential and incidental damages is expressly disclaimed. John Deere’s liability in all events is limited to and shall not exceed the purchase price paid. Warranty Disclaimer. John Deere has made a diligent effort to provide product information and illustrate the products in this literature accurately; however, such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are merchantable, or fit for a particular purpose, or that the products will necessarily conform to the illustrations or descriptions. Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made or authorized by John Deere. 4-Inch Angle Grinder Operator's Manual Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. While John Deere attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them. Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. While John Deere attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable national and local codes and regulations, and be sure that the product, installation, and use will comply with them. Prompt Disposition. John Deere will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be defective within limited warranty. For any product believed to be defective within limited warranty, first write or call d...
Эта инструкция также подходит к моделям:Шлифовальные станки - AT-3303-J (314.73 kb)