Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Screen Support the picture size of a normal screen (4:3). LCD (Liquid Crystal Display) Designed with color TFT liquid crystal display 3learly shows the data. Stereo amplifier Built-in 2x1.5 W speakers. NOTE: It s normal for a TFT screen to experience some light or dark spots appearing on the LCD screen. 2 Front/Top/Side Panel Unit View 1.AV/TV button Press to select AV or TV mode. 2. MENU button Press to shwo menu. 3. VOL-/+ button Press to decrease / increase volume. Press to make adjustment while working with menu. 4. CH -/+ button Press to select channels. Also work as direction buttons while working with menu. 5. POWER Switch Press to turn power on/off. 6. LCD Screen Present high resolution pictures. 7. Speakers Two speakers produce stereo sound. 8. Remote sensor Sense remote signal. 9. Power On Indicator in normal playback status, it lights green, while in the standby mode, turns red. 10. RF IN Jack Connect to external antenna to receive TV program in TV mode. 11. VIDEO IN Jack Connect to external video input. 12. AUDIO IN Jacks Connect to external audio input. 13. PHONE Jack Connect to stereophone. 14. DC 12V IN Jack Connect to power supply 3 Rear Panel Using Stand There is a stand on the back of the unit to support the player. a) Lift up the stand from its groove. d) Erect the unit by supporting it against the stand. z) Aslopewise viewing position is realized. Unit View -Attaching Hole 4 Remote Control Remote Control Drawing COBY (call) |menu)J ■■© © © Pi 3......i © © © © © © © © ■© ÜD TF-TV505 1. CALL: Press to show current program number. 2. TV/AV: Press to select TV or AV. 3. Numeric key pad: Press to input number. 4 . MENU: Press to enter menu setup window. 5. VOLUME+/-: Press to adjust sound level. 5. CHANNEL +/-: Press to select channel. 7. RECALL: Press to view previous program. 5 Remote Control Remote Control Preparation of Remote Control Take the back cover off of the remote control and insert supplied coin battery and put on the cover. (Refer pg6 for detail) Using Remote Control Point the remote to the sensor by about 60 degrees of no more than 7 meters COBY © H M ® ® '5 S ® ® ® > IIJ (1) 1») ® ® © ® The operating distance may vary depending to the brightness around. Notes: a) Do not point bright lights directly at the remote control sensor. b) Do not place objects between the remote control unit and the remote control sensor. c) Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment. 7 Power Connections Connect to AC adaptor **Do not connect the power cord until all other connections have been made. Power is supplied through the provided appropriative power adapter, one end of which is connected to the DC IN jack on the main unit, another to wall outlet with AC100-240V. Note: a. If you have difficulty inserting the plug, turn it over and reinsert it. b. If the unit will not be in use for long periods of time, disconnect the plug from the outlet. c. In order to prolong the operation life, the intervals of continuous power on should be not less than 30s. 8 Power Connections Battery pack connection a) Match the four hooks to its attaching slots on the bottom of the main unit. b) Slide downward to lock it into position. c) To release the battery, press it upward. Please refer to below diagram for better understanding. Press it upward to release. \ I Press it downward to lock. Using battery pack a) Loosen the screw. b) Slide the cover downward to open the battery pack. c) Insert ten batteries. d) Slide the pack cover up to lock it. e) Tighten the screw. Screw Cable Connections Cable connections Connecting an External Aerial Antenna or Cable Television To view television channels, a signal must be received by the device from one of the following sources: The internal antenna An outdoor aerial antenna A cable television network A satellite network 1. Connect the supplied antenna adaptor into the "RF IN" jack located on the side of this device. 2. Connect the external antenna source to the adaptor. Connecting Audio and Video sources (DVD Player, VCR, Game Console, Etc.) 1. Using the supplied composite cable, connect the yellow video plug into the "VIDEO IN" and the black audio plug into the "AUDIO IN" jack located on the side of this device. 2. On the other end of the cable, connect the yellow plug into the "VIDEO OUT" and the red and white plugs into the "AUDIO OUT" of your DVD player, VCR, game console, etc. 3. Connect audio sources (including DVD/VCR/CAMCORDER/PC) to "AUDIO IN" ports by RCA cable. 4. Connect video sources (DVD/VCR/CAMCORDER) to the "VIDEO IN" port. 10 TV Function TV Function Basic Operation 1. Connect the TV RF source to the RF IN jack on the unit side panel. 2. Connect the power supply cord. If the player is in standby mode, set POWER switch to "ON 3. Press the AV/TV...