Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
8. Type the path that matches the CD-ROM drive on your system, and then click OK. For example, enter the following path: E:\ In this example, the letter E: is the CD-ROM drive. 9. Click Close in the Network Dialog box when the copying process is complete. 10. When prompted to restart your computer, click Yes. The system restarts using the new driver and the default configuration settings. Windows NT driver software 4-8 Moving the Network Card to a Different Slot Before moving your GA622T Copper Gigabit Ethernet Card to a different slot in the same system, you must first remove the card driver software. After removing the driver software, you can move the card to a different slot and reinstall the driver software. To remove the driver software: 1. Start your Windows NT system and log in. You must have Network Administrator privileges to remove the driver software. 2. On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel. The Control Panel window opens. 3. Double-click the Network icon. The Network dialog box opens. 4. Click on the Adapter tab. Any previously installed driver is listed in the Network Adapters list. 5. Click on the network card you want to remove, and then click Remove. Repeat step 5 for each network card that you want to remove. 6. Click Close. 7. When prompted to restart your computer, click No. 8. Shut down your computer. Install the network card in a new slot by following the instructions in “Installing Your Copper Gigabit Ethernet Card” on page 2-7, and then install the network drivers by following the instructions in “Installing the Driver Software” on page 4-1. Windows NT driver software 4-9 CHAPTER 5: WINDOWS 2000 DRIVER SOFTWARE This chapter provides information about the Microsoft Windows 2000 driver software. This chapter also describes how to: • Install the driver software in the Windows 2000 environment • Move the card to a different slot • Remove the driver software Note: The GA622T Copper Gigabit Ethernet card must be physically installed in your server or workstation prior to installing the driver software. See Chapter 2 “Hardware Installation” for details. Installing the Driver Software When the Windows 2000 system first boots up after installing a new hardware device, such as a GA622T Copper Gigabit Ethernet Card, the system automatically detects the new hardware and prompts you to install the driver software for the device. A network driver must be installed before the GA622T Copper Gigabit Ethernet Card can be used with your Windows 2000 system. You must have Network Administrator privileges to install the driver software. Windows 2000 driver software 5-1 To install the card software for Windows 2000, perform the following procedure: 1. When you boot up the Windows 2000 system after installing the GA622T Copper Gigabit Ethernet Card, a series of Found New Hardware Wizard dialog boxes are displayed. Windows 2000 driver software 5-2 2. In the Install Hardware Device Drivers dialog box, click “Search for a suitable driver for my device (recommended),”and then click Next. Windows 2000 driver software 5-3 3. In the Locate Driver Files dialog box, check the “Specify a location” box. 4. Insert the GA622T Copper Gigabit Ethernet Card Driver and Documentation CD into your CD-ROM drive and click OK. Windows 2000 driver software 5-4 5. In the Driver Files Search Results dialog box, verify that the correct path to the driver software is shown, and then click Next. Windows 2000 driver software 5-5 6. Click Finish to complete the installation. Moving the Network Card to a Different Slot Windows 2000 automatically detects the installation and removal of hardware. To move a GA622T Copper Gigabit Ethernet Card to a different slot in the same system, you need to do the following: 1. Shut down the system and remove the card from the PCI slot. 2. Install the card in its new PCI slot (see “Installing Your Gigabit Ethernet Card” on page 2-7). 3. When the system is powered on, reinstall the driver software (see “Installing the Driver Software” on page 5-1). Windows 2000 driver software 5-6 Removing the Driver Software Under Windows 2000, the driver software is automatically uninstalled when its hardware is removed. To remove a card, do the following: 1. Shut down the system and remove the card from the PCI slot. 2. When the system is powered on, the driver will be automatically uninstalled. Windows 2000 driver software 5-7 CHAPTER 6: NETWARE DRIVER SOFTWARE This chapter provides information about the Novell NetWare driver software. This chapter also describes how to: • Verify the NetWare pre-installation requirements • Install the driver software in the NetWare environment • Modify Driver properties during the driver software installation Because network administrators can use more than one method to install device drivers on a NetWare server, this chapter does not provide detailed installation instructions for each method. Each method is briefly describe...