Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If your computer does not support the passphrase, then you will need to type the encryption key in order to join the wireless network. • Key 1–Key 4. These values are not case-sensitive. You can manually enter the four data encryption keys. These values must be identical on all computers and access points in your network. Enter 10 hexadecimal digits (any combination of 0–9, a–f, or A–F). 5. Select which of the four keys will be the default. Data transmissions are always encrypted using the default key. The other keys can be used only to decrypt received data. The four entries are disabled if WPA-PSK or WPA authentication is selected. 6. Click Apply to save your settings. Extender IP Address Setup Select extender Maintenance > IP Address to display the following screen: The IP Address screen shows whether the extender is set to get its IP address dynamically from the router (this is the most common setting), or is set as a static IP address. • Get Dynamically From Router. The wireless network router assigns an IP address when the extender connects to its wireless network. Most networks are set up so that the router automatically does this. • Use Static IP Address. Specify a static IP address. This is not usually necessary. If you set this up, you should be technically experienced or have a technically experienced person help you. -IP Address. The static IP address. -IP Subnet Mask. The subnet mask associated with the IP address. -Gateway IP Address. The IP address for the gateway. -Primary DNS. The primary domain name server (DNS). -Secondary DNS. The secondary domain name server (DNS). Status Screen When you connect to after the automatic firmware check, the Status screen displays. You can also select Maintenance > Status to display this screen: This screen shows the current settings and the status of your extender. You can click Show Statistics to see device performance statistics such as the number of packets sent and number of packets received for each port. See Show Statistics on page 21. The following table describes the fields in the Status screen. Table 2. Status Settings Field Description Hardware Version The hardware version of the extender. Firmware Version The current firmware version of the extender. If you upgrade the firmware, this field changes. GUI Language Version The language version running on the extender. If you upgrade the firmware, this field changes. Connection Status to Existing Network Name (SSID) Your extender is set up to connect to this SSID, also called the wireless name. Connection Status The status of your wireless connection (connected or disconnected). Link Rate The actual transmission (Tx) and receive (Rx) link rate in the current wireless connection. Extender PC Info MAC Address The physical address of the extender, as seen from the local area network (LAN). IP Address The IP address of the extender. The default is 192.168.1.250. DHCP Server Identifies the network DHCP server on the wireless network. IP Subnet Mask The IP subnet mask associated with the LAN IP address of the extender. The default is 255.255.255.0. Gateway IP Address The IP address of the wireless network gateway. Domain Name Server The IP address of the Domain Name Server (DNS) of the wireless network. Extender Wireless Settings Name (SSID) The name (SSID) or the wireless network. Region The location where the extender is operating. Channel The channel of the wireless network. Wireless AP On or Off. Broadcast Name On or Off. Wi-Fi Protected Setup Configured. Show Statistics On the Status screen, click Show Statistics to display the following screen: Table 3. Show Statistics Fields Field Description LAN or WLAN (Port) The statistics for the LAN (local), and wireless LAN (WLAN) ports. For each port, the screen displays the following: Status The link status of the port. TxPkts The number of packets transmitted on this port since reset or manual clear. RxPkts The number of packets received on this port since reset or manual clear. Collisions The number of collisions on this port since reset or manual clear. Tx B/s The current line utilization—percentage of current bandwidth used on this port. Rx B/s The average line utilization for this port. Up Time The time elapsed since the last power cycle or reset. Poll Interval Specify the poll interval frequency. If you change this value, click Set Interval so that your change takes effect. Network Devices Select Maintenance > Network Devices to display the following screen: Back Up and Manage Extender Settings Select Maintenance > Backup Settings to display this screen. The Backup and Restore options in the Backup Settings screen let you save and retrieve a file containing your extender’s configuration settings. Once you have your extender working correctly, you should back up the information to have it available if something goes wrong. When you back up the settings, they are saved as a file on your computer. You can restore the device’s set...