Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
original integrity and has a maximum dimension of 18 feet (5.49m) and a maximum wall height of 42 inches (1.07m). 2. WARNING -To reduce the risk of injury, do not permit children to use this product unless they are closely 4. Do not install within an outer enclosure or beneath supervised at all times. the skirt of a hot tub or spa unless so marked. 3.CAUTION -This pump is for use with permanently 5. SAVE THESEinstalled pools and may also be used with hot tubs and INSTRUCTIONS. spas if so marked. Do not use with storable pools A permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. 06/02 97490081 INSTALLATION & OPERATING INSTRUCTIONS GENERAL Your AQUA-FLO pump has been quality built and engineered to give maximum efficiency under normal water pumping conditions. Consult the manufacturer for any other applications. LOCATION OF PUMP For best pump performance, locate the system as close to the water source as possible. Provide adequate access around the pump for inspection and maintenance. MODELS LESS TRAP This model was designed for below water level (flooded suction) applications. Make sure the pump is installed at a level that will allow the pump casing (volute) to completely fill with water. Two quick disconnect compression fittings are included with your pump for ease of installation and maintenance. Make sure the fittings are correctly aligned with pump connections to allow the O-ring to make the proper seal. Hand tighten only. Do not use a wrench to tighten fittings. MODELS WITH TRAP Avoid excessive tightening of pipe or fittings in threaded suction port in trap. For threaded connection, use Quick-Seal Teflon Thread Sealing Compound, Plasto- Joint Stick or any other sealants formulated specifically for plastics. STARTING & PRIMING PUMP Do not run unit dry. Always be certain that the pump casing and/or trap is filled with water before starting the unit. Allow a reasonable amount of time for priming. If pump will not start, or will not prime, see trouble shooting below. MAINTENANCE The trap basket should be inspected frequently and kept clean. To avoid damage to the basket, do not strike when cleaning. Inspect trap cover O-ring regularly and replace as necessary. Keep motor clean. Insure that louvered openings are free from debris and obstructions. Over a period of time, the shaft seals may become damaged or worn and must be replaced. WINTERIZATION To prevent damage during freezing conditions, turn off all electrical power. Drain thoroughly and clean out any debris. Protect pump and motor from elements by covering or, if possible, store in a dry, well ventilated room. WARNING - All electrical wiring of the motor installation must be done by a qualified electrician in accordance with applicable electrical codes. Before working on any motor, be certain that the source of electrical power is off at the main junction box. BONDING WIRE - Upon installation of the pump, the motor must be bonded with a No. 8 AWG (8.4mm2) solid copper conductor per National Electric Code. The connection should be from the accessible wire connector on the motor to all metal parts of the swimming pool, spa, or hot tub structure and to all electrical equipment, metal conduit and metal piping within 5 feet (1.5m) of the inside walls of a swimming pool, spa or hot tub, when the motor is installed within 5 feet of the inside walls of the swimming pool, spa, or hot tub. NOTE: For electrical connections, see wiring diagram on motor rating plate. TROUBLE SHOOTING MOTOR WILL NOT START: 1.) Check Circuit Breakers 2.) Check for incorrect or loose wire connections. 3.) Make sure the correct power supply is being used. 4.) Any on/off switch or pneumatic switch should be in the "on" mode. MOTOR OVERHEATING AND CYCLING ON AND OFF: 1.) Check for incorrect or loose wire connections. 2.) Check for low voltage supply (frequently caused by undersized wire). 3.) Make sure the motor gets a fresh air supply and the vents are kept unclogged. MOTOR MAKES HUMMING NOISE BUT WILL NOT START: 1.) Make sure motor shaft turns free. 2.) Check for jammed impeller or an obstruction in (volute) casing. 3.) Check for low voltage and undersized wire. PUMP WILL NOT PRIME: 1.) Make sure pump is installed at the proper level and the plumbing lines have been correctly installed to allow the water to enter pump freely. 2.) Open air control valves to release any possible air lock. 3.) Make sure all suction and discharge lines are clear and unobstructed and all valves are opened. 4.) Check for air leaks in the suction line. LOW WATER FLOW: 1.) Check filter pressure gauge; filter may need cleaning. 2.) Check for clogged plumbing lines. 3.) Check for worn or damaged impeller. 4.) Check for low voltage. WATER LEAKS 1.) Check contamination or damage to shaft rotary seal. Replace if necessary. 2.) Check compression fitting (union connectors); make sure they are properly aligned and secured. Hand tight...