Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD is centered. Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws slightly each time until all are snug to ensure even pressure. Make certain the SEAL (9) is properly seated in recess of spout base. (A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions below to secure faucet to mounting surface. (B) Installation less ESCUTCHEON (1). Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and mounting surface. Do not use putty. 4 5 8 6 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. 7 4 5 8 6 7 9 10 3 2 On model with separate spray, place the SPRAY HOLDER (1) into the appropriate mounting hole. Assemble the SPRAY HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1) from below and hand tighten. Do not use putty. For installation less spray, cap off SPRAY HOSE CONNECTION (3) with PIPE CAP (4). 3 INSTALL SPRAY HOLDER 1 1 2 5 4 2 TEST INSTALLED FAUCET Move HANDLE down into "off" position and remove AERATOR (1). Turn on water supplies and check connections for leaks. Operate HANDLE (2) up and down, left and right to flush water lines thoroughly. For faucet with spray, direct SPRAY HEAD (3) into sink and activate SPRAY (3). Check hose connections for leaks. Move HANDLE (2) down to "off" position and replace AERATOR (1). CHECK CONNECTIONS FOR LEAKS 6 3 4 CONNECT HOSE SPRAY Feed SPRAY HOSE (5) through SPRAY HOLDER (1) and attach COUPLING NUT (6) of HOSE (5) to SPRAY HOSE CONNECTION (3) on valve body. Tighten COUPLING NUT (6) firmly. 2 SPRAY HOSE CONNECTION MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot (Marked with a Red Line) and right supply to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. Faucet supplies are 21" long from faucet base. Note: If additional supply length is required, installer must purchase additional parts separately. Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking. M965115_Rev.1.2 1 2 COLD HOT 3 M965115_Rev.1. 2 Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O-RINGS. First turn off water supply. Remove HANDLE BUTTON (2) and loosen SET SCREW (1) with 2.5mm HEX WRENCH (11) supplied. Pull HANDLE (3) off valve stem. Pull off CAP (4). Loosen CARTRIDGE SCREWS (5) and remove CARTRIDGE (6). Remove SPOUT (7) by pulling up gently while moving SPOUT (7) side ...
Эта инструкция также подходит к моделям:Сантехника - QUINCE 4433.001 (249.43 kb)
Сантехника - QUINCE 4433.001 (249.43 kb)
Сантехника - QUINCE 4433.001 (249.43 kb)