Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
‘Move’ button Use this button to use the move function. If you press the ‘Move’ button, as the nozzle is moved back and forth while you operate the rear cleansing/front cleansing function, you can clean a wider area. 7 8 ‘Nozzle Position’ button Use this button to control the nozzle position during the rear cleansing/front cleansing operation. You can move the nozzle in 5 levels using the ‘Nozzle Position’ button. ‘Wide’ button Use this button to control the water ejection range when using the cleansing function. You can select the angle of the water in 3 levels using the Wide function button (Straight LineLevel 1Level 2). Whenever this button is pressed, the Wide function indicator turns a different color. 9 ‘Water Temp.’ button Use this button to control the water temperature. Whenever the ‘Water Temp.’ button is pressed, you can control the water temperature in 4 levels (LMHOff). . For the BA13-BR/BE only 10 ‘Seat Temp.’ button Use this button to control the seat temperature. Whenever the ‘Seat Temp.’ button is pressed. You can control the seat temperature in 4 levels (LMHOff). 11 ‘Sterilization’ button Use this button to perform the sterilization function. Sterilizing water is ejected for 30 seconds to sterilize and clean the nozzle. 12 ‘Deodorization’ button Use this button to perform the deodorization function. When you press this button, the deodorization function is performed for approximately 1 minute. . For the BA13-BR/BE only . For the BA13-BR/BE only 15 Using your bidet Using the rear nozzle Using the rear nozzle 1. Sit down on the seat and press the ‘Rear Cleansing’ button on the operation part. 2. Self-cleaning for the rear cleansing nozzle is performed, removing the cold water remaining inside the nozzle before the water stream is ejected so that the water can be set to a desired temperature for cleansing. 3. The cleansing water is ejected for approximately 1 minute and then stops automatically. 4. Self-cleaning for rear cleansing nozzle is performed for approximately 5 seconds after rear cleansing. Then the nozzle retracts itself. 5. You can adjust the nozzle position by pressing the ‘Nozzle Position’ button. 6. You can adjust the water ejection angle by pressing the ‘Wide’ button (for the BA13-BR/BE only). The cleansing water ejection time may be delayed while the above functions are performed. Tips If the ‘Rear Cleansing’ button is pressed again during the cleansing operation, the rear cleansing function operates for another 1 minute. While cleansing, users can adjust the water temperature, water pressure, and nozzle position according to their preferences. You can not increase the water pressure level higher than level 2 if your area is in the following conditions. - Main water supply temperature under 10 . and rated power source under 110 V~. If the seat sensor does not detect a human body, the bidet will not work. Tips Moving Press the ‘Move’ button on the operation part. - The nozzle moves back and forth, providing a wider range of cleansing. This will operate for as long as the rear cleansing function continues. You can control the nozzle position by pressing the ‘Nozzle Position’ button. To stop the move function, press the ‘Move’ button once again. Drying Press the ‘Dry’ button on the operation part. - Warm air is emitted for approximately 2 minutes. If you wipe off the water lightly before turning on the air dryer, drying will finish faster. You can control the air temperature by pressing the ‘Dry Temp.’ button. If you press the ‘Dry’ button again during the operation, additional drying starts for another 2 minutes. If you press the ‘Dry’ button while cleansing, cleansing is stopped and drying starts immediately. Stopping To stop the current operation, press the ‘Stop’ button. - This stops all currently operating functions. The drying function stops 2 seconds after the ‘Stop’ button is pressed. 16 Using your bidet Using the front nozzle Using the front nozzle 1. Sit down on the seat and press the ‘Front Cleansing’ button on the operation part. 2. Self-cleaning for the front cleansing nozzle is performed, removing the cold water remaining inside the nozzle before the water stream is ejected so that the water can be set to a desired temperature for cleansing. 3. The cleansing water is ejected for approximately 1 minute and then stops automatically. 4. Self-cleaning for rear cleansing nozzle is performed for approximately 5 seconds after front cleansing. Then the nozzle retracts itself. 5. You can adjust the nozzle position by pressing the ‘Nozzle Position’ button. 6. You can adjust the water ejection angle by pressing the ‘Wide’ button (for the BA13-BR/BE only). The cleansing water ejection time may be delayed while the above functions are performed. Tips If the ‘Front Cleansing’ button is pressed again during the cleansing operation, the front cleansing function operates for another 1 minute. While cleansing, users can adjust the water temperature, water pressure, and nozzle positio...
Эта инструкция также подходит к моделям:Сантехника - BA13-BR (3.07 mb)
Сантехника - BA13-AR (3.07 mb)
Сантехника - BA13-AE (3.07 mb)