Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
. . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete Installation Instructions continued . . . Step 2: Mounting frame to wall 1. Remove the eight Torx-head screws securing the panel to the frame, and remove the panel (see Figure 3). Note: Scuff panel does not need to be removed. 2. Position the frame against the wall, ensuring that it is level. If necessary, insert shims under the frame until level. Note: When mounted, the Standard and Juvenile Height frames should rest on the floor. IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frameto bend. If necessary, install shims to compensate for any walldistortion. 3. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind the frame to ensure that it will not bend when anchored. 4. Once you have positioned the frame such that it is level and resting on the floor, and flat against the wall or shimmed, use four 3/8" bolts and washers to mount the frame to the wall (see Figure 4). Figure 4 (4) 3/8" BOLT AND WASHER FRAME Figure 3 PANEL FRAME (8) TORX-HEAD SCREW SCUFF PANEL (do not remove) 4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV Installation Instructions continued . . . Step 3: Installing bowl assembly IMPORTANT: Moving and positioning the bowl will require more than one person. Note: Refer to Figure 5 below when installing the bowl assembly. 1. With someone to assist you, place the bowl assembly squarely onto the frame. 2. Attach the front of the bowl assembly to the frame using the two 1/4"-20 x 3/8" pan-head screws and washers. Do not tighten screws at this time. IMPORTANT: When bolting the bowl assembly to the frame and wall, do not overtighten bolts. Overtightening bolts can damage the Terreon® material. 3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied by the installer) to bolt the bowl to the wall anchors. 4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame. Do not overtighten. BACK VIEW 3/8" BOLT AND WASHER BOWL ASSEMBLY 3/8" BOLT AND WASHER 1/4"-20 X 3/8" PAN HEAD SCREWS AND WASHERS Figure 5 Installation Instructions continue . . . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete Installation Instructions continued . . . Step 4: Connecting supply and drain 1. FOR HOT AND COLD SUPPLY: Connect the flexible hoses installed to the Vernatherm™ Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a). Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet. FOR SINGLE TEMPERED SUPPLY: Attach the stop/check/strainer to the 1/2" tempered supply line. Connect the stop/check/strainer to the solenoid valves with the flexible supply hose (see Figure 6b). 2. Install the drain plug in the hole in the bottom of the bowl (see Figure 7). 3. Beneath the bowl, install the 1/4" rubber washer onto the drain plug, and thread the tailpiece to the drain plug. 4. Assemble the P-trap by connecting the 1-1/2" tubular pipe to the tailpiece and to the 1-1/2" drain pipe stubbed out of the wall. 5. Install the strainer on the drain plug opening inside the bowl, and push the strainer firmly into place. Figure 6a VERNATHERM™ THERMOSTATIC MIXING VALVE FLEXIBLE SUPPLY HOSE FLEXIBLE SUPPLY HOSE CONNECT TO 1/2" NPT HOT CONNECT TO 1/2" NPT COLD WATER SUPPLY WATER SUPPLY Figure 7 FLEXIBLE SUPPLY HOSE (TO SOLENOID BRACKET) Figure 6b STOP/STRAINER/CHECK VALVE (S60-003) 90° ELBOW 169-639 1/2 NIPPLE (113-006DJ) 4/24/08 Bradley Corporation • 215-1243 Rev. E; EN 08-805 Express® Lavatory System SS-Series Installation - Obsolete SS-2/IR/STD, SS-2/IR/JUV Installation Instructions continued . . . Step 5: Connecting electrical and supply tubing WARNING: The Express® must be connected to the 24 VAC Class II plug-in transformer provided. Connection to 110 VAC can result in damage to the electronics and cause personal injury. CAUTION: Connection of leads other than shown may cause permanent damage to the sensor. 1. Snap the sensor circuit plug from the sprayhead into the solenoid circuit plug located on the valve bracket. 2. Snap the transformer circuit plug into the female transformer circuit plug located on the valve bracket. 3. Insert the two sprayhead supply tubes into the two solenoid tube connectors by loosening the compression nut and firmly pushing the tubing into the tube connector until the tubes are fully seated, then re-tighten the compression nut (hand-tight and then two full turns with a wrench) (see Figure 8). Step 6: Completing installation 1. Turn on the water supply to the Express® and check for leaks. 2. Turn on the electrical power to the electrical outlet and pass your hand in front of each station’s senso...
Эта инструкция также подходит к моделям:Сантехника - SS-2/IR/JUV (206.18 kb)