Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
It will instruct you on howto operate and service your machine safely and correctly. Failure to do so could result in personal injury and/orequipmentdamage. A This SAFETY-ALERT symbol means ATTENTION! BE ALERT! YOUR SAFETY IS INVOLVED! A CAUTION: All hardware is metric. Only metric tools should be used. Other tools that do not fit properly can slip and cause injury. Right-hand and left hand sides of the implement are determined by facing in the direction the implementwill travel when going forward. When you see this symbol, be alertto the possibility of serious bodily injury or death. Carefully followthe instructions in the safety message. This machine is of metric design. However, for your convenience, most specifications are given in metric measurements with thecustomary U.S. measurements following. See Complete Warranty found on the inside back cover. Record your implement model and serial number in the space provided below. Yourdealerneedsthis information to give you prompt, efficient service when you order parts. MODEL NO. SERIAL NO. DATE PURCHASED. This Product is manufactured exclusively for Simplicity by Befco, Inc. Please submit warranty and parts requests through your local dealer directly to: Befco, Inc. 1781 S Wesleyan Blvd PO Box 6036 Rocky Mount, NC 27803 Telephone: 252-977-9920 Fax: 252-977-9718 2 DEALER CHECKLIST To the Dealer: Inspect the machinethoroughly after assemblyto assure it is functioning properly before delivering it to the customer. The following checklist is a reminder of points to cover. Check off each item as it is found satisfactory or after proper adjustment is made. PREDELIVERY CHECKLIST □ 1. Gearbox oil level □ 2. Guards and shields properly fastened □ 3. Lubrication of grease fittings □ 4. All hardware properly tightened □ 5. All decals properly located and readable DATE SET UP SIGNATURE □ 6. Blades properly installed and tightened □ 7. Otheradjustmentsformachinelevel, height, PTO length, etc. □ 8. Overall condition (touch up any scratches, clean and polish) □ 9. Test run, check for excessive vibration or overheating of bearings □I 10. Operator's Manual DELIVERY Review the operator's manual with the customer. Explain the following: □ 1. Simplicity warranty □ 2. Safe operation and service □I 3. Correct machine installation and operation □ 4. Daily and periodic lubrication and maintenance □ 5. Correct lubricants □ 6. Daily and periodic inspections □ 7. Troubleshooting □ 8. Removing and storing machine □I 9. Simplicity parts and service □ 10. Have the customer write the machine model and serial number in space provided in manual introduction □ 11. Give customerthe operator's manual and encourage the customer to read the manual carefully □ 12. Remove and file this page DATE DELIVERED_ SIGNATURE_(Dealer) SIGNATURE_(End User) Model No. Serial No. 4 TABLE OF CONTENTS INDEX 1.0 - General Information Page 6 1.01 -Safety Symbols 6 1.02 -General 6 2.0 - Safety Decals 8 2.01 - Safety Precautions and warning and safety decals 8 3.0 - Operation 9 3.01 - Setup and Lubrication 9 3.02 - Side Shift 11 3.03 -Depth control 12 3.04 - Rearshield adjustments 12 3.05 - Pre-operational checklist 13 3.06 - Attaching to the tractor 13 3.07 - Operating technique 14 3.08 -Test Run 14 3.09 - Setting Depth 14 3.10 -Working Speed 14 3.11 -Finer Pulverization 14 3.12 -Headland Procedure 14 3.13 - Gullies or Ditches Procedures 15 3.14 -Working limitations 15 3.15 -Transporting 15 3.17 - Safety Shear pin Coupler 15 4.0 - Maintenance 16 4.01 -Lubrication 16 4.02 - Blades 17 4.03 - Storage 18 -Torque Specifications 19 -Troubleshooting 20 -Parts Breakdown 22 -Warranty Registration 31 -Warranty 33 GENERAL INFORMATION Thank you and congratulations for having chosen our tiller. Your new side shift tiller is a technologically advanced machine constructed of high quality sturdy components and will fulfill yourworking expectations. Read this manual carefully. It will instruct you on howtooperate and service your machine safely and correctly. Failure to do so could result in personal injury and or equipment damage. 1.01 - Safety Symbol A This symbol means ATTENTION, BE ALERT! YOUR SAFETY IS INVOLVED! A CAUTION CAUTION Is used for general reminder of good safety practices, or to direct attention to unsafe practices. A WARNING WARNING denotes a specific potential hazard. A DANGER DANGER denotes the most serious specific potential hazard. 1.02 - General A CAUTION CAUTION: All hardware is metric. Only metric tools should be used. Other tools that do not fit properly can slip and cause injury. Right hand and left hand sides of the implement are determined by facing in the direction the implement will travel when going forward. 6 SAFETY DECALS Fig. 2 Safety Decals; Replace Immediately if Damaged A DANGER ROTATING BLADE HAZARD To prevent serious injury or death from Rotating blade: •Do not go under frame whe...