Оценок - 6, средний балл: 3.2 ( )

Производитель: Tanaka Размер: 598.68 kb Название файла: 1415e4d9-910a-28f4-5525-bf274af6d49d.pdf Язык инструкции:

The spark plug should be replaced after about 100 operation hours or earlier if the electrodes are badly eroded. NOTE! In some areas, local law requires using a resistor spark plug to suppress ignition signals. If this machine was originally equipped with resistor spark plug, use same type of spark plug for replacement. Muffler (Fig. 3-4) Remove the muffler and remove excess carbon from the exhaust port or muffler inlet every 100 hours of operation. Cylinder (Engine cooling) (Fig. 3-5) The engine is air cooled, and air must circulate freely around engine and over cooling fins on cylinder head to prevent overheating. Every 100 Operating hours, or once a year (more often if conditions require), clean fins and external surfaces of engine of dust, dirt and oil deposits which can contribute to improper cooling. NOTE! Do not operate engine with engine shroud or muffler guard removed as this will cause overheating and engine damage. 11 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN Oiler port (Fig. 5-1) Clean the chain oiler port (1) whenever possible. Guide bar (Fig. 5-2) Before using the machine, clean the groove and oiler port (1) in the bar with the special gauge offered as an optional accessory. Side case (Fig. 5-3) Always keep the side case and drive area clean of saw dust and debris. Periodically apply oil or grease to this area to protect from corrosion as some trees contain highlevels of acid. Angle transmission (Fig.5-4) Check angle transmission or angle gear for grease level about every 50 hours of operation by removing the grease filler plug on the side of angle transmission. If no grease can be seen on the flanks of the gears, fill the transmission with a quality lithium based multipurpose grease up to 3/4. Do not completely fill the transmission. Spark Arrestor If your unit comes with spark arrestor screen and yet your local regulation requires use of spark arrestor for prevention against a possible fire, please attach it to the muffler by removing muffler protector and other related parts. [The spark arrestor meet the regulation of SAE J335-SEP90 and CSA CAN3-Z62.1-M77.] 12 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN CHAIN SHARPENING Parts of a cutter. (Fig. 4-1, 2) WARNING! Gloves should be used when sharpening chain. 1. Top plate 2. Working corner 3. Side plate 4. Gullet 5. Heel 6. Chassis 7. Rivet hole 8. Toe 9. Depth gauge 10. Correct angle on top plate (degree of angle depends on chain type) 11. Slightly protruding "hook" or point (curve on non-chisel chain) 12. Top of depth gauge at correct height below top plate 13. Front of depth gauge rounded off LOWERING DEPTH GAUGES WITH A FILE 1) If you sharpen your cutters with a file holder, check and lower the depth. 2) Check depth gauges every third sharpening. 3) Place depth gauge tool on cutter. If depth gauge projects, file it level with the top of the tool. Always file from the inside of the chain toward an outside cutter. (Fig. 4-3) 4) Round off front corner to maintain original shape of depth gauge after using depth gauge tool. Always follow the recommended depth gauge setting found in the maintenance or operator manual for your saw. (Fig. 4-4) GENERAL INSTRUCTIONS FOR FILING CUTTERS File (1) cutter on one side of the chain from the inside out. File on forward stroke only. (Fig. 4-5) SHARPENING ANGLES FOR SHARPENING SAW CHAIN (Fig. 4-7B) 5) Keep all cutters the same length. (Fig. 4-6) 6) File enough to remove any damage to (~) 6 cutting edges (side plate (1) and top plate (2)) of cutter. (Fig. 4-7) 13 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit. • Clean the chain oil filter port. • Clean the groove and oil filter port in the guide bar • Clean the side case of saw dust. • Check that the saw chain is sharp. • Check that the bar nuts are sufficiently tightened. • Make sure that the chain transport guard is undamaged and that it can be securely fitted. • Check that nuts and screws are sufficiently tightened. Weekly maintenance • Check the starter, especially cord and return spring. • Clean the exterior of the spark plug, • Remove the spark plug and check the electrode gap. Adjust it to 0.6 mm (.024.), or change the spark plug. • Clean the cooling fins on the cylinder and check that the air intake at the starter is not clogged. • Clean the air filter. Monthly maintenance • Rinse the fuel tank with gasoline, and clean fuel filter. • Clean chain oil filter. • Clean the exterior of the carburetor and the space around it. • Clean the muffler of carbon. 14 custsvc@tanaka-ism.com Owner.s Manua...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: