Оценок - 2, средний балл: 4 ( )

Производитель: Tanaka Размер: 598.68 kb Название файла: Язык инструкции:

CAUTION! When the chain is excessively tightened the bar and chain will be damaged rapidly. Conversely, when the chain is excessively loosened, it may get out of the groove in the bar. Always wear gloves when touching the chain. WARNING! During operation, hold the unit firmly with both hands. A single hand operation may cause serious injury. 5 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN 4. Operating procedures Fuel (Fig. 2-1) WARNING! The chainsaw is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel • Always use branded 89 octane unleaded gasoline. • Use Tanaka two-cycle oil or a quality two-cycle oil at mixing ratio of 25-50:1 (Gasoline (A) : Oil (B)), only forthe state of California at 50:1. • Never use multi-grade oil (10 W/30) or waste oil. • Always mix fuel and oil in a separate clean container. • Always start by filling half the amount of fuel, which is to be used. Then add the whole amount of oil. Mix (shake) the fuel mixture. • Add the remaining amount of fuel. • Mix (shake) the fuel-mix thoroughly before filling the fuel tank. Fueling WARNING! • Always shut off the engine before refueling. • Slowly open the fuel tank, when filling up with fuel, so that possible over-pressure disappears. • Tighten the fuel cap carefully, after fueling. • Always move the unit at least 3 m (10 ft.) from the fueling area before starting. Before fueling, clean the tank cap area carefully, to ensure that no dirt falls into the tank. Make sure that the fuel is well mixed by shaking the container, before fueling. 6 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN CHAIN OIL (Fig. 2-2) Fill the chain oil reservoir (2). Always use good quality chain oil. When the engine is running, the chain oil is automatically discharged. NOTE! Add chain oil when its level lowers to one centimeter from bottom. (Fig. 2-2) ADJUSTMENT OF CHAIN OIL SUPPLY The chain oil quantity discharged through the lubrication system is factory-adjusted to the maximum. Adjust the quantity in accordance with the operating condition. • Loosen the fixing screw (2) one turn. (Fig. 2-3) • Turn the adjusting screw (3) clockwise to decrease the quantity and turn it counterclockwise to increase the quantity. (Fig. 2-4) • Do not try to turn the screw (3) clockwise beyond 1 turn from it.s most counterclockwise position or the maximum quantity discharged position. • After adjustments have been made, tighten fixing screw (2). (Fig. 2-3) NOTE! When you have lost the proper position of the screw (3), start with the most counterclockwise position. 7 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN Starting (Fig. 2-5) CAUTION! Before starting, make sure the cutting attachment does not touch anything. 1 . Set ignition switch (1) to ON position. (Fig. 2-5) *Push priming bulb (4) several times so that fuel flows through the bulb or return pipe. (if so equipped) (Fig. 2-6,7) 2. With the safety trigger (2) pressed (if so equipped), pull throttle trigger and push throttle lock (3), then slowly release the throttle trigger first, then the safety trigger. This will lock the throttle in starting position . 3. Set choke lever to CLOSED position (5). (Fig. 2-6,7) 4. Pull recoil starter briskly, taking care to keep the handle in your grasp and not allowing it to snap back. 5. When you hear the engine want to start, return choke lever to RUN position (open). Then pull recoil starter briskly again. NOTE! If engine does not start, repeat procedures from 2 to 5. 6. After starting engine, pull throttle trigger to release throttle lock. Then allow the engine about 2-3 minutes to warm up before subjecting it to any load. NOTE! Throttle limiter (4) is to adjust maximum opening of throttle. At the factory it is adjusted at its full opening. (Fig. 2-5) Stopping (Fig. 2-8) Decrease engine speed and run at an idle for a few minutes, then turn off ignition switch. A cutting attachment can injure while it continues to spin after the engine is stopped or power control is released. When the unit is turned off, make sure the cutting attachment has stopped before the unit is set down. 8 custsvc@tanaka-ism.com Owner.s ManualTPS-2501,TPS-2510.TPS-250PN,TPS-270PN TPS-2501,TPS-2510.TPS-250PN,TPS-270PN SAFE OPERATION • Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. DO NOT operate unit if any wires(power, telephone, cable, etc.) are closer than 15M (50ft.) to any part of the operator or unit. (Fig.2-9) • Spectator and fellow workers must be warned, and children and animals prevented from coming nearer than 15M (50ft.) while the pole saw is in use. (Fig.2-10) • Avoid all power lines. This unit is n...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: