Оценок - 5, средний балл: 3
(
)
)
|
Фрагмент инструкции
iäÜE ^mSSÜJÜfc,, (F1) (2)fSS (3)±fil (4) £11 1. $ff3MSttä?±W&4. (F2) tea?, (F2) (3)«ST (5>3i«att i?fT(M5 X 25)@$o (F3) (DilfT (2)*® (3)±BÜ (4)££i3® AB £ 1. mmtj, (F4) 2. am 13 English $ z. 5. SET UP ■ ADJUSTING THE THROTTLE CABLE 1. After releasing the throttle lever, pull the throttle wire. The normal play is 1 or 2mm when measured at the carburetor side end. 2. If the play is short or long, take off the air cleaner cover, loosen the lock nut and adjust the play. (F5) (1) Adjust nut (2) Lock nut 5.i££ 1. «PTiP/'Éffi, AM-b'fiü —JtWiS, —/USA 1 ~ 2 iR-feo 2. ü, (F5) (DÍI31S«« (2)0$«« ■ PROTECTOR ■ {£#■£ Wrap the waist pad around the shaft (F6) tube. (F6) (1) Protector (1) ftp* ■ INSTALLING THE ANTICAUGHT UP COVER (F7) 1. Match the inside ditch of the anticaught up cover to the outside projection of the gear case and push it in until it touches the stopper.. 2. Tighten the screw on the cover front. (1) Anti-Caught Up Cover (2) Stopper (3) Gear case ■ SWIVEL LOCK This brushcutter is equipped with the swivel lock to fix the hanger and the main pipe at the optional position. (F8) • In the ordinary operation, use it with the wing nut of the hanger front loose (unlocked). • In transportation, please tighten the wing nut when it is necessary to fix the main pipe. (1) Wing nut (2) Loose (unlock) (3) Lock ih 2. (2)8* ■&3&8II (F8) • aurffcüíW, «ataai o&ji&íü!) mmM. (Di»»«« (,2)®m№№) mmm 14 English 5. SETUP ■ INSTALLING THE METAL BLADE (F9) 1. Set the inner holder to the gear shaft, and turn to fix with the attached L-shaped bar. 2. Put the blade on the inner holder with the face with letters to the gear case, and match correctly the hole of the blade to the projection of the inner holder. 3. Set the outer holder to the gear shaft with the hollowed face to the blade. 4. Put the attached bolt cover on the outer holder and secure it with the bolt (left screw) together with the spring washer and the washer. (1) Bolt (2) Spring Washer (3) Washer (4) Bolt cover (5) Outer holder (6) Blade (7) Gear shaft (8) Bar (9) Inner holder (10) Gear case ■ INSTALLING THE NYLON CUTTER (OPTION) (F10) 1. Set correctly the inner holder and the outer holder to the gear shaft. 2. Screw the attached bold (M8 Left) into the gear shaft and secure it with the spanner. 3. Screw the nylon cutter into the bolt by fixing the inner holder with the L-shaped bar and tighten it manually. | NOTE ~] Keep bolts and washers to install the blade carefully so as not to lose them. (1) Inner holder (2) Outer holder (3) Bolt (4) Nairon cutter (5) Nairon cord 5. i££ 2. fflJJttflftlEfiltlfegiE Zltttt3l5#iWü8P±„ 3. «tt±. 4. if (mm) ±m± (D«t* (2)3¥*!&ffi (3)&B (4)«&* <5)*Mt (6) Tin <7)** (8) LÜIÄ (9) Aft (10)15*« ■Jg£M 7] (F10) 2. (M8© «■AÄifettrt, Äffl 3. (Drttt (2)*Mt (3 )«& (4)jg^*JI (5)/sse^ 15 English Ф £ 4. FUEL 4.Л |Awarning~1 • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. • Make sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. Ш н нтяятл SL^ppo шттшш&мршя'Хо |IMPORTANT • Never use oil for 4 cycle engine use or water cooled 2-cycle engine. • Never use "FUEL WITH NO OIL (RAW GASOLINE)11. • Never use fuel laced with water. • Mixed fuels which have been left unused for a period of one month or more may clog the carburetor or result in the engine failing to operate properly. Put remained fuel into an air-tight container and keep it in the dark and cool room. • Please ask for “mixed gasoline for air-cooled 2-cycle engines” at your nearest gas station, or use fuel made by putting unleaded gasoline for automobiles and air-cooled 2-cycle engine oil into a mixing container in accordance with the following ratios and then shaking to mix well. Mixing ratios: When using Zenoah genuine 2-cycle oil (FC grade): 50:1 (100 ml of oil for every 5 liters of gasoline) S Ш *ШЁЯ43Ф8#1Й. (ШНШ) . RBftJMfc. етвшяшжешййшм п*2№В51*ш*?т шт Л£ЯЗЕЯЛй№1^#2Я1вЗ|ад1 ЙШТЬЬЯЯЛН-вв, ш inffifflZenoah 2ДО|8ШЕШЙ( FC^) 50:1 ( НШ51: #lffi100ml) ОДЯШ18в№#а№й( FB4K) : 25:1 ( Я?Й41-: ШЙ160т1) When using commercially available 2-cycle oil (FB grade): 25:1(160 ml of oil for every 4 liters of gasoline) 16 English 7. OPERATION ■ STARTING THE ENGINE | A warning] • Before starting the engine, inspect the entire unit for loose fittings or fuel leaks, and the cutting attachment is properly installed and securely fastened. • Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. 1. Turn the cap to the fuel tank to make sure that it is fixed on tightly. (F11) (1) Cap (2) Fuel tank 2. Open the fuel tank cock. (F12) 3. Move the choke lever to the closed position. (F12) (1) Choke lever (2) Fuel cock (3) Close (4) Open (5) Close (6) Ope...