Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
n Always make sure the cutting attachment shield is properly installed before operating this unit. Operating Units with a Blade The blade rotates counter-clockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. Position the blade so cuts are made between the blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 10 o’clock and 5 o’clock positions. WARNING! When cutting wood with a saw, feed the blade slowly—never strike or “slam” a spinning blade against the wood. WARNING! DO NOT use 2-tooth or non-Shindaiwa approved 4-tooth cutting blades with Shindaiwa trimmers and brushcutters. Blade Thrust ‘Blade thrust’ is a sudden sideways or backward motion of the brushcutter. Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS! Brushcutter Handlebar A brushcutter handlebar or barrier bar helps prevent the operator from moving forward, or the unit moving rearward, thus preventing inadvertent bodily contact with the blade. ALWAYS KEEP THE HANDLEBAR OR BARRIER BAR SECURELY IN PLACE ON THE UNIT! Brushcutter Shoulder Strap A shoulder strap provides additional protection against blade thrust. In addition, a shoulder strap gives significant support and comfort to help ensure safe and efficient operation. When operating a C3410 with a blade, make sure both the handle and shoulder strap are adjusted to the size of the operator using the unit. Ten O'clock Eight O'clock Five O'clock DONOTCUT OK To Cut Blade Rotation Figure 26 Vertical Cuts Hold the brushcutter with the blade at a 90° angle to the ground so the blade’s bottom edge rotates toward the operator. Move the blade from top to bottom through the cut, and cut only with the bottom edge of the blade. General Maintenance IMPORTANT! MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM. Blades Keep blades sharp and check blade condition frequently. If a blade’s performance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade IMMEDIATELY! Daily Maintenance WARNING! Before performing any maintenance, re- pair or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance work. WARNING! Non-standard parts may not operate properly with your unit and may cause damage and lead to personal injury. WARNING! n Never repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury. Prior to each work day, perform the following: n Remove dirt or debris from the engine, check the cooling fins and air cleaner for clogging and clean them as necessary. 10-Hour Maintenance (more frequently in dusty conditions) 1. Remove the air cleaner cover by loosening the two thumbscrews. See Figure 8A. . Remove and inspect the pre-filter. If the pre-filter is torn or otherwise damaged, replace it with a new one. See Figure 8B. 3. Clean the pre-filter with soap and water. Let dry before reinstalling. 4. Inspect the air cleaner element. If the element is damaged or distorted, replace it with a new one. 5. Tap filter gently on a hard surface to dislodge debris from element or use compressed air from the inside to blow debris out and away from the air filter element. n Carefully remove any accumulation of dirt or debris from the muffler or the fuel tank. Dirt build-up in these areas could cause engine overheating, induce premature wear, or create a fire hazard. Unscrew Fasteners Figure 28A IMPORTANT! Direct the air stream at the inside face of the filter only! 6. Install the filter element, pre-filter and cover in the reverse order of removal. NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. Muffler This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. n Blades are not interchangeable between Shindaiwa edgers and trimmer/ brushcutter models. Operating any unit with a blade or attachment not approved for that unit can be hazardous and may cause serious injury. n Check for loose or...
Эта инструкция также подходит к моделям:Садовые инструменты - 81714 (2.68 mb)
Садовые инструменты - 81714 (2.68 mb)
Садовые инструменты - 81714 (2.68 mb)
Садовые инструменты - 81714 (2.68 mb)