Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
For cor otation speed of the engine and interferes with cutting efficiency, as well as increasing the risk of tic shield will cut the nylon string to optiinjury. mum length; a string that is too long reduces the 2 3 4 10 Apply the nylon string head as shown in the illustration: 1) Upper plate 2) Nylon string head. Tighten by turning counterclockwise. As you tighten, hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. Do not use the nylon string head guard extension (H) with metal blades. Assemble blade as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16). If you want to assemble the rotating mower gauge,proceed as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Assembly of sawtooth blade and blade guard When using the sawtooth blade, remove the guard for the line cutter head and grass cut- ting blade and replace the flange guard (A) with the sawtooth blade guard (H). Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and there- fore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart. For assembly see figures (E7, E8). 2 3 4 10 2 3 4 10 F. Starting and stopping the engine position with the other starter string ar until you encounter some r cord sharply and forcefully (to start the engine 1 5 6 7 8 9 10 11 12 14 CAUTION! Start the brush cutter in a flat place. During startup stand in a stable position. Make sure the blade or nylon string head do not touch the ground or any obstacles. when Do not pull the starter cord all the way and do not release it abruptly against the machine as this could damage it. Startup of cold engine F1. Stop switch (A) turned to "I" opposite the "STOP" mark. F2. Turn the fuel enrichment lever (B) to the closed position. F3. Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm (C). The diaphragm need not be completely filled. Push the decompression valve (D) down if your models is fitted with one. Pull the cord until the engine starts. Let the motor run for a few seconds and accelerate. This will automatically return the fuel enrichment lever to its original position. The cutting devices are now rotating. Startup of warm engine F1. STOP switch turned to "I" (START). Throttle trigger lever in minimum position (released). Enrichment lever (B) in original position. F3. Repeat item F3 in the previous paragraph. Stopping the engine F5. Turn the stop switch to "O" (STOP). ENGLISH - 6 After stopping the engine the rotating parts, firmly until they stop. In case of emergency the blade or nylon string head, keep spinning above delay can be abbreviated by scraping the by inertia for a few seconds. Grip the machine blade supporting cup parallel on the ground. G. Carburetor adjustment Your machine can be equipped with a low emis- sion carbur any adjustment of the carbur ly by an authorized service center of special equipment f...
Эта инструкция также подходит к моделям:Садовые инструменты - 953900756 (1.31 mb)
Садовые инструменты - 953900757 (1.31 mb)
Садовые инструменты - 953900758 (1.31 mb)
Садовые инструменты - 953900759 (1.31 mb)