Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Route the clutch cable through guide with the adjustment at the top. See Figure 1. 6. Install the handle bar cross brace between the handle bars using four 1/4” - 20 x 1 1/2” hex bolts, nuts, and lock washers. See Figure 1. 7. Route the throttle control cable under the handle passing under the cross brace. 8. Tighten all bolts at this time. 9. Install clutch cable by hooking loop at bottom into notch in clutch arm. Hook spring into clevis and into hole in clutch lever. The clutch cable should be adjusted so that the belt will slip when released and the spring will be extended 1/4” when lever is engaged. 10. Install handle bar grips (Some type of lubricant such as liquid soap will be helpful). FINAL SETUP 1. Check the transmission to that it is full. See Figure 3. a. Remove check plug. b. Use 90 wt. gear lube or 50 weight motor oil. Approximately 1 pint. c. Fill until check plug overflows. d. Replace plug. 2. Remove the engine dipstick and fill crankcase with oil according to engine owner’s manual. 3. Fill fuel tank. Use clean, fresh, lead-free, gasoline. Fill the tank completely. DO NOT MIX OIL WITH GASOLINE. MT and TP Models RMT Ref# Part # Quan. Description Part # Quan Description 101 336682 1 Main Frame Rail LH 102 336681 1 Main Frame Rail RH 103 359335 2 Frame Spacer 302 130695 1 Handle Bar LH 162081 1 Handle Bar Left Hand 303 336678 2 Handle Bar Brace 304 130730 1 Handle Cross Brace 305 313786 2 Handle Grip 4 308 130694 1 Handle Bar Right Hand 162082 1 Handle Bar RH Heavy Duty 402 162077 1 Intek Throttle Control 403 402014 2 #10 - 3/8” Slot Tapping Screw 404 336683 1 Clutch Lever 405 359345 1 Clutch Lever Pin 407 359346 1 Clutch Locking Pin 408 359359 1 Clutch Locking Spring 409 359327 1 Clutch Cable Spring 410 162041 1 Clutch Cable and Adjustment 413 359326 2 Clutch Cable Guide 414 359323 1 Throttle Cable Clip 601 162031 2 Wheel, 10” x 1.75 162065 2 Wheel, 10” x 1.75” Heavy Duty 605 461467 1 Wheel Yoke Locking Pin 606 359362 1 Lock Pin Spring 607 461468 1 Cotter Pin 609 162032 1 Wheel Yoke Assembly 162033 1 Wheel Yoke Assembly 615 130701 2 Hitch Casting 618 336686 1 Depth Bar 621 359363 1 Depth Bar Adjust. Spring 625 461469 1 Depth Bar Adjust. Pin 705 359321 1 Idler Pulley 338009 1 Idler Pulley 706 162069 1 Idler Shaft 708 359325 1 Idler Shaft Arm 709 400290 1 Capscrew NC, 3/8” x 1 3/4” 802 359330 2 Wheel Shoulder Bolt 804 400184 2 Cap Screw, NC 5/16” x 3/4” 805 400186 1 Cap Screw, NC 5/16” x 1” 400190 Cap Screw, NC 5/16” x 1 1/4” 806 400197 1 Cap Screw, NC 5/16” x 2 1/4” 807 400200 4 Cap Screw, NC 5/16” x 2 1/2” 809 400207 2 Cap Screw, NC 5/16” x 3 3/4” 811 400275 1 Cap Screw, NC 3/8” x 3” 813 400115 5 Cap Screw, NC 1/4” x 1 1/2” 814 400109 1 Cap Screw, NC 1/4” x 1 3/4” 816 443101 6 Nut, NC 1/4” 817 443106 11 Nut, 5/16” 818 443110 2 Nut NC, 3/8” 819 444721 4 Locknut NC, 3/8” 820 444720 1 Locknut NF, 3/8” 821 446130 6 Lockwasher, 1/4” 822 446136 11 Lockwasher, 5/16” 825 455050 1 Washer SAE Flat, 1/2” 830 162096 Optional LH Tine Shield 831 1...
Эта инструкция также подходит к моделям:Садовые инструменты - MT50B (1.09 mb)
Садовые инструменты - MT50B (1.09 mb)
Садовые инструменты - RMT50B (1.09 mb)
Садовые инструменты - RMT50IC (1.09 mb)