Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации Maxim, модель RMT50B

Производитель: Maxim
Размер: 1.09 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


5. As the engine warms up, move the throttle lever to desired position. Alllow engine warm-up period before operating tiller. NOTE: A warm engine may start without choking. Do not use the choke if engine is hot. Stopping Engine 1. Move the throttle control to rear position. 2. Push stop switch at spark plug. 3. Disconnect the wire from the spark plug to prevent accidental starting of the machine while it is unattended. OPERATION OF THE CHAIN DRIVE TILLER DANGER 1. When the ground is hard (especially during spring and fall plowing), place wheels in up position by pulling To prevent personal injury, the chain drive spring loading pin and lifting wheels. Release pin. For must disengage immediately when clutch leweeding or cultivating, wheels may be left down if you ver is released. If it does not, stop the tiller, prefer. adjust belt and cable tension as described in Adjustments section of this manual. 2. Adjust the drag stake for comfortable operation. Never leave the tiller unattended with the This is done by depressing pin, and sliding the drag engine running. Children are attracted to a stake up or down. The drag stake should be set so that running tiller and could be injured if struck when it is firmly in the ground, and your hands are on by the rotating tines. the tiller handle, your arms hand comfortably with the elbows slightly bent. 3. Move throttle control to center position. Start the engine and allow it to warm up, then set the throttle at WARNING about half speed. After you have become more familiar TRANSMISSION 130400 REF # PART # QUAN. DESCRIPTION 1 130693 1 Left hand Case Assembly 2 130692 1 Right Hand Case Assembly 3 359312 1 Oil Fill Plug 4 400201 1 5/16” x 2 3/4” Bolt 5 455041 1 5/16” Washer 6 443106 1 5/16” Nut 7 359306 2 Dust Shield 8 359305 2 Oil Seal 9 359304 2 Bearing, Needle 10 359313 AR Washer 11 359303 1 Spacer 12 162038 1 Shaft and Sprocket Assembly 13 359302 1 Chain 14 336675 1 Gasket 15 359296 1 Chain 16 162023-A 1 Idler Sprocket Cluster 17 359297 2 Input Bearing 18 359298 1 Bushing, Idler Cluster 20 162037 1 Input Shaft/Sprocket 21 359339 1 Washer Rubber Seal 22 408883 1 1/4” x 1/2” Screw 23 359351 1 Input Shaft Spacer 24 455049 AR Shim Washer 41/64 x 1 x .0625 455062 AR Shim Washer 41/64 x 1 x .032 25 359299 2 Transmission Washer with the tiller, you may want to run the engine a little Keep hands clear of belt and tines faster. while engine is running. Never 4. Press down firmly on the handles, and then squeeze attempt to adjust or clean tines the clutch lever. The tines will begin to turn, but the while engine is running, at risk of tiller should not move forward. If it does, don’t pull severe injury. backwards - merely press down harder on the handle. *AR -- As Required When you find the right amount of downward pressure so that the tines are digging and tiller is not moving forward, release the pressure slightly. As you release it you’ll notice the tiller beginning to move forward. The whole tilling operation is co...

Эта инструкция также подходит к моделям:
Садовые инструменты - MT50B (1.09 mb)
Садовые инструменты - MT50B (1.09 mb)
Садовые инструменты - RMT50B (1.09 mb)
Садовые инструменты - RMT50IC (1.09 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории