Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
x Do not stand or climb on this product when raised. x Do not place any part of your body under any part of this product unless this product is securely resting on adequate blocking or on the ground. x Do not use blocking made of concrete blocks, logs, buckets, barrels or any other material that could suddenly collapse or shift positions. Do not use wood or steel blocking that shows any signs of material decay. Do not use blocking that is warped, twisted, or tapered. x Never operate controls from the ground. Operate the controls only from the operator’s station. x Never leave equipment unattended with the engine running or with this product raised on the loader. x Be aware of the added weight and width of this product. Reduce travel speeds accordingly, especially when traveling over rough ground. x Keep this product close to the ground and under control when transporting. 3 4 SAFETY INSTRUCTIONS WORK SAFELY - A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST ACCIDENTS !! WARNING SECTION [CONTINUED] WARNING Obey all the safety instructions listed in this section and throughout this manual. Failure to obey instructions in this section could result in death or serious injury. WHEN DEALING WITH HYDRAULICS DURING ANY TYPE OF ASSEMBLY, OPERATION, MAINTENANCE, OR OTHER WORK ON OR NEAR THIS PRODUCT: .. Hydraulic fluid under pressure can penetrate the skin and cause serious injury or death. Hydraulic leaks under pressure may not be visible! .. If any fluid penetrates the skin, GET IMMEDIATE MEDICAL ATTENTION!! .. Wear safety glasses, protective clothing, and use a sound piece of cardboard or wood when searching for hydraulic leaks. DO NOT USE YOUR HANDS! .. Before connecting or disconnecting hydraulic hoses, read your tractor or power unit’s operator’s manual for detailed instructions on connecting and disconnecting hydraulic attachments. .. Make certain that all parts meet the specifications for this product when installing or replacing hydraulic hoses or fittings. .. After connecting hydraulic lines: .. Slowly and carefully raise the loader and cycle the rollback / dump cylinders to check hose clearances and to check for any interference. .. Operate the hydraulics on this product to check hose clearances and to check for any interference. .. Make certain that the hoses cannot interfere with or actuate the quick-attach mechanism. .. Make certain that hoses will not be pinched, or get tangled, in any equipment. .. Do not lock the auxiliary hydraulics of your power unit in the “ON” position. .. Refer to your power unit’s operator’s manual and this manual for procedures and intervals, then inspect and maintain the entire hydraulic system to insure that the fluid remains clean, that all devices function properly, and that there are no fluid leaks. WHEN MOUNTING THIS PRODUCT TO YOUR POWER UNIT: .. Refer to the operator’s manuals of your power unit, your loader, and your quick-attach for special or detailed mounting instructions. .. This product should fit onto the quick-attach or loader arms of your power unit the same as the original products that were designed by your loader / quick-attach manufacturer. .. If this product does not fit properly, contact FFC Attachments before operating. .. Never place your finger into the mounting plate or 3- point hitch or loader holes. A slight movement of the power unit or this product could cause serious injury. BEFORE EACH USE, THOROUGHLY INSPECT THIS PRODUCT AND: .. Make certain that all safety signs are in place and legible. Refer to the safety sign page in this manual for the placement of safety signs for this product. .. Replace all damaged or excessively worn parts and hardware only with genuine FFC Attachments parts or with properly rated fasteners, hydraulic hoses, or fittings. .. Make certain that all locking pins, latches, and connection devices are properly installed and secured. .. Make certain that all protective guards, canopies, doors, etc., are in place and secure. WHEN OPERATING THIS PRODUCT IN ACCORDANCE WITH DESIGN INTENTIONS: .. Keep everyone at least nine feet away from the unit when operating. WHEN ADJUSTING, SERVICING OR REPAIRING THIS PRODUCT: .. Make no modifications to your Roto-Tiller. .. When making repairs, use only genuine FFC Attachments parts or, for fasteners, hydraulic hoses, or hydraulic fittings, use only properly rated parts. .. Replacement parts, for parts with safety signs attached, must also have safety signs attached. SECTION 2 CAUTION Obey all the safety instructions listed in this section and throughout this manual. Failure to obey instructions in this section may result in personal injury. .. Do not use the top of this product as a step. Under certain conditions, this area can be slippery. 5 SAFETY SIGN LOCATIONS ITEM QTY. PART # DESCRIPTION 1 1 50-0723 READ MANUAL 2 1 50-0724 HYDRAULIC 3 2 RDL3100 STAND CLEAR 4 1 RDL3178 NOT A STEP INSTRUCTIONS .. Keep all safety signs clean and legible. .. Replace all missing, illegible, or damaged safet...
Эта инструкция также подходит к моделям:Садовые инструменты - LAF3438 (631.4 kb)
Садовые инструменты - LAF3468 (631.4 kb)