Оценок - , средний балл: ( )

Инструкция по эксплуатации Symbol Technologies, модель C350

Производитель: Symbol Technologies
Размер: 2.33 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

T350 (1) Loosen the 2 joint bolts fully. JOINT BOLT JOINT GROUND WIRE THROTTLE GRIP (2) Slip the outer tube into the joint until the tube bottoms. The outer tube or gearcase shaft may have to be rotated slightly for the splines on the mainshaft to fully engage to the engine. Assembly of the Outer Tube C350/B450 (1) Loosen the 2 joint bolts fully and slip the outer tube into the joint until the tube bottoms (up to the insert label). The outer tube or gearcase shaft may have to be rotated slightly for the splines on the mainshaft to fully engage the engine. (2) Attach the ground wire to the joint bolt. (3) Tighten the 2 joint bolts securely. (6) Slip the right-side handlebar into the throttle grip. Locate the throttle grip so that the stopper bolt can pass through the stopper hole. Securely tighten the stopper bolt and nut. (7) Securely tighten the clamp bolt. JOINT BOLT GROUND WIRE (3) Attach the ground wire to the joint bolt. (4) Tighten the 2 joint bolts securely. (5) Loosen the screw which tightens the throttle lever to the outer tube. Shift the throttle lever toward the blade. (6) Put the throttle cable into the tube. Push throttle cable through hole in rear grip. (7) Set the throttle cable onto the throttle lever. Use the wrench so that the wire edge goes into the slot of the throttle lever securely. INSERT LABEL GROUND WIRE SCREW Assembly of the Handle T350 Assembly of the Handle C350/B450 Throttle Cable Adjustment (1) Pull the throttle trigger gently, and check for free-play of approximately 5mm. (2) If free-play is out of specifications: (a) Slide the cable cap toward the muffler side until the adjusting nut and the lock nut appear. (b) Loosen the lock nut slightly. (c) Turn the adjusting nut so that free-play is about 5mm. (d) Then, tighten the lock nut. (e) Slide the cable cap back. (1) Loosen the two bolts of the lower cap and remove the lower cap. (2) Position the handle bracket against the handle label located on the outer tube. (3) Attach the lower cap with the two bolts and tighten the bolts. Make sure the front handle is in position per the illustration. (4) Secure the cable to the outer pipe with the two bands as the illustration shows. The two bands are in the tool bag. WARNING! NEVER operate this machine without the front handle. Operating without the front handle may result in serious injury. NOTE: Tighten four bolts diagonally to properly secure the handle. NOTE: Adjust the handle at the best position for operator comfort. (1) Put four square nuts in the recesses on the underside of the barrier. (2) Fit the handle and barrier over the outer tube and tighten four bolts in a crisscross fashion. HANDLEBARHANDLE BRACKETHANDLE LABELLOWER CAPBOLTTHROTTLE GRIP HANDLE OUTER TUBE BARRIER BARRIER BOLT BAND NUT THROTTLE CABLE CABLE CAP ADJUSTING NUT LOCK NUT Cutting Attachment Shield Assembly WARNING! NEVER operate this machine without the cutting attachment shield. Operating without the cutting attachment shield may result in serious injury. WARNING! Carefully inspect the cutting attachment shield assembly to make sure it is tightened securely and does not wobble. CAUTION! The line cutter is attached to the shield extension and must be used when operating with a trimmer head. (A) Cutting Attachment Shield (1) Insert the cutting attachment shield between the outer tube and the lower clamp. Loosen the nut and bolt which are tightening the lower clamp if the cutting attachment shield does not fit with the lower clamp. NOTE: It may be necessary to loosen the lower clamp bolt so that the shield will fit between the tube and clamp. (2) Fit the two spacers (T350 only) and the upper clamp over the outer pipe and tighten with four bolts. NOTE: Tighten four bolts a crisscross fashion. (3) Tighten the lower clamp bolt and nut securely. CUTTING ATTACHMENT SHIELD BOLT OUTER TUBE UPPER CLAMP CUTTING ATTACHMENT SHIELD HOOK RECEIVER SPACER BOLT SPACER HOOK LOWER CLAMP NUT (B) Shield Extension (when trimmer head is in use) (1) Attach the shield extension to the cutting attachment shield. NOTE: Make sure the shield extension is completely hooked at the hook receiver. SHIELD EXTENTION Installing a Blade WARNING! Never operate this machine without the safety clip in place. (1) Make sure the switch is off and the engine is stopped. (2) Wear gloves to protect your hands. (3) Turn the unit over so the saw holder flange extending from the gear case is facing up. (4) Using the small end of the plug wrench, loosen the bolt (turn clockwise) and remove the bolt, bolt guard, and holder B. (5) Slide the safety clip as shown in the illustration. WARNING! Before operating, make sure the blade is securely mounted. Turn the blade with your hand slightly and make sure the blade turns smoothly without wobbling. (6) Fit the blade over the safety clip onto holder A. Then, slide the safety clip back to its original position. WARNING! The blade must fit flat. Make sure the direction of the arrow indicated on the blade corresponds with t...