Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Avoid operating the engine at low speeds. Doing so can lead to rapid clutch wear. In addition, slow-speed operation tends to cause grass and debris to wrap around the cutting attachment. (1) After starting the engine, pull the throttle lever gradually. The engine speed increases and the blade will start rotating. (2) When the throttle lever is released, the engine goes back to idle speed automatically. (3) Operate the machine at full throttle while cutting. Best fuel efficiency is obtained by releasing the throttle when swinging back after cut. (4) The blade rotates counterclockwise. For best performance and to minimize being stuck by debris, move the blade from right to left while advancing on your work. WARNING! Position the blade so cuts are made between blade’s 8 o’clock and 10 o’clock positions (as viewed from above). DO NOT cut between the 11 o’clock and 5 o’clock positions. Ten O'Clock Direction of Rotation DO NOT CUT WARNING! “BLADE THRUST” is a sudden sideway or backward motion of the machine. Such motion may occur when the blade jams or catches on an object such as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE THRUST AND GUARD AGAINST ITS EFFECTS. OK TO CUT Eight O'Clock WARNING! NEVER strike or slam the spinning blade against the wood. CAUTION! DO NOT use 2-tooth blades with this machine. WARNING! When transporting, make sure the engine is not running and blade is covered with blade cover. Using a Brushcutter With a Trimmer Head Maintenance Engine Operating Speeds Operate at full throttle while cutting grass. You may install one of several types of Shindaiwa trimmer heads on your TC350/B450 trimmer or brushcutter, each with features for specific applications and/or operational requirements. For proper operation, always refer to the instructions accompanying the trimmer head being used. Available trimmer head styles include: . Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation. . Manual. The operator indexes line manually with the grass trimmer stopped. . Fixed. The operator must stop the unit and add new lengths of trimmer line manually. . Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to the head by pivots. WARNING! Before performing any maintenance, repair, or cleaning work on the machine, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance work. CAUTION! Operation at low rpm can lead to premature clutch failure. Trimming and Mowing Grass Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut. To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line. Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer head horizontal. WARNING! Never repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury. CUTTINGPATHRETURNPATH23041 Daily Maintenance Prior to each work day, perform the following: . Remove the dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean them as necessary. . Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Dirt buildup in these areas can lead to engine overheating, fire, or premature wear. . Check for loose or missing screws or components. Make sure the cutting attachment is securely fastened. . Check the machine for leaking fuel or grease. CAUTION! Do not push the rotating line into trees, wire fences or any material that could tangle or break line ends. Edging Tilt the handle about 100° to the left (from horizontal) and move forward, holding the trimmer or brushcutter vertically as shown. 23042 10 Hour Maintenance Muffler Maintenance 50 Hour Maintenance (350 only) Remove the air cleaner element from the carburetor and clean it thoroughly with soap and water. Squeeze out excess, let dry and reassemble the element. Cleaning Remove and clean the cylinder cover and clean grass and dirt from the cylinder fins. Hard starting or a gradual loss of performance can be caused by carbon deposits lodged in the muffler’s spark arrester screen. In such cases, performance can usually be restored by removing the spark arrester screen and giving it a thorough cleaning with a stiff bristle brush. If carbon deposits are severe or if no performance improvement is noted, your unit should be returned to your Shindaiwa dealer for inspection. MUFFLER COVER BOLT STAY CAUTION! Do not operate the machine if the air cleaner or element is damaged, or if the element is water-soaked. CYLINDER COVER PROTECTOR BOLT GASKET CLEANER ELEMENT Muffler CLEANER COVER Remove the cutting attachment and the gear shaft collar, and press new grease into the gear case until the old grease has been pushed out. Use only lithium base grease (such as Shind...
Эта инструкция также подходит к моделям:Садовые инструменты - B450 (2.33 mb)
Садовые инструменты - C350 (2.33 mb)