Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
3) Installing or removing driver bit or drill bit Always use the side grip to ensure operating safety. (Fig. 5 & 6) Install the side grip so that the teeth on the grip fit in Important: between the protrusions on the tool barrel. Then tighten Always be sure that the tool is switched off and the bat- the grip by turning clockwise at the desired position. It tery cartridge is removed before installing or removing may be swung 360° so as to be secured at any position. the bit. Adjustable depth rod (Fig. 4) Turn the sleeve counterclockwise to open the chuck jaws. The adjustable depth rod is used to drill holes of uniform Place the bit in the chuck as far as it will go. Turn the depth. Loosen the thumb screw, set to desired position, sleeve clockwise to tighten the chuck. To remove the bit, then tighten the thumb screw. turn the sleeve counterclockwise. When not using the driver bit, keep it in the bit holders. Bits up to 45 mm long can be kept there. Switch action (Fig. 7) CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the trigger. Tool speed is increased by increasing pressure on the trigger. Release the trigger to stop. Reversing switch action (Fig. 8) CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. • When not operating the tool, always set the reversing switch lever to the neutral position. This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for forward rotation or from the B side for reverse rotation. When the switch lever is in between (the neutral position), the switch trigger cannot be pulled. Speed change (Fig. 9) To change the speed, first switch off the tool and then slide the speed change lever to the “II” side for high speed or “I” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. CAUTION: • Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned half-way between the “I” side and “II” side, the tool may be damaged. • Do not use the speed change lever while the tool is running. The tool may be damaged. Selecting the action mode (Fig. 10) This tool employs an action mode changing ring. Select one of the three modes suitable for your work needs by using this ring. For rotation only, turn the ring so that the arrow on the tool body points toward the M mark on the ring. For rotation with hammering, turn the ring so that the arrow points toward the X on the ring. For screw- driving (rotation with clutch), turn the ring so that the arrow points toward the U mark on the ring. CAUTION: Always set the ring correctly to your desired mode mark. If you operate the tool with the ring positioned half-way between the mode marks, the tool may be damaged. Adjusting the fastening torque (Fig. 11) The fastening torque can be adjusted in 16 steps by turning the adjusting ring so that its graduations are aligned with the arrow on the tool body. The fastening torque is minimum when the number 1 is aligned with the arrow, and maximum when thenumber 16 is aligned with the arrow. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. Screwdriving operation (Fig. 12) First, turn the action mode changing ring so that the arrow on the tool body points to the U marking. Adjust the adjusting ring to the proper torque level for your work. Then proceed as follows. Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. NOTE: • Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. • When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart below. Nominal diameter Recommended size of wood screw (mm) of pilot hole (mm) 3.1 2.0 – 2.2 3.5 2.2 – 2.5 3.8 2.5 – 2.8 4.5 2.9 – 3.2 4.8 3.1 – 3.4 5.1 3.3 – 3.6 5.5 3.6 – 3.9 5.8 4.0 – 4.2 6.1 4.2 – 4.4 • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Drilling operation First, turn the action mode changing ring so that the arrow on the tool body points to the M marking. The adjusting ring can be aligned in any torque levels for this operation. Then proceed as follows. • Drilling in wood When drilling in wood, best results are obtained with wood drills equipped wit...