Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
370 m/min for hard wood, plastics and non-ferrous metals (with special band saw blade); . 800 m/min for all kinds of wood. A Caution! The drive belt must not run in a diagonal position; this will damage the belt Setting knob for drive belt tension With the setting knob (30) the drive belt tension is corrected, if necessary: . turning the setting knob clockwise lessens the blade tension; . turning the setting knob counterclockwise increases the blade tension. Saw table tilt After loosening the locking screw (31) the saw table (32) tilts steplessly through 45° against the blade. 4. Special product features 5. Transporting the saw 6. Machine details 23 24 25 26 27 28 29 370 m/min 800 m/min 30 19 ENGLISH Rip fence The rip fence (33) is clamped to the front. The rip fence can be used on both sides of the blade. ADanger! Start the saw only after the following preparations have been completed: . the saw is fastened; . the saw table is installed and aligned; . the V-belt tension checked; . the combination switch/plug is installed; . the safety devices have been checked. Connect the saw to the mains supply only after all of the above preparations are completed! Otherwise there is a risk of an unintentional starting of the saw, which may cause severe personal injury. 7.1 Mounting For a firm stand the saw must be mounted on a stable supporting surface: 1. Drill four holes in the supporting surface. 2. Put fixing bolts through the base plate and secure with nuts. Optimal working height and stability is provided by the workstand (optional accessory), which is already prepared for mounting the saw. 7.2 Saw table installation 1. Fit limit stop screw (34) to the underside of the saw table. 2. Guide saw table over the band saw blade and place it on the table trunnion. 3. Attach the saw table with four each screws (35) and washers to the table trunnion. 7.3 Saw table alignment The saw table needs to be aligned in two planes . laterally, in order for the blade to run dead centre through the table insert; . at right angles to the band saw blade. Saw table lateral alignment 1. Loosen the four fastening screws (36) that hold the lower table trunnion. 2. Align saw table so that the blade runs through the centre of the table insert's slot. 3. Tighten the four fastening screws (36) again. Aligning the saw table at right angles to the band saw blade 1. Raise upper blade guide fully (see “Operation”). 2. Check band saw blade tension (see “Initial operation”). 3. Loosen locking screw (37). 4. Using a try square, set the table at right angles to the blade and tighten the locking screw (37) again. 5. Loosen locking nut (38) and adjust limit stop screw (39) until it touches the saw housing. 6. Tighten locking nut. 7. Initial operation 31 32 33 428 mm 312 mm 458 mm 342 mm 34 35 36 37 39 38 20 ENGLISH 7.4 Fence guide extrusion installation • Fasten the fence guide extrusion (40) with four each thumb screws and washers to the saw table. 7.5 Rip fence installation The rip fence can be used on both sides of the blade. 1. Fasten the fence extrusion (41), using . two each pan-head screws, . two each washers and . two each knurled nuts to the fence guide. 2. Attach the thus assembled rip fence with one each . pan-head screw, . washer and . wing nut to the fence guide extrusion (42). Rip fence alignment 1. Loosen the two small knurled nuts (43) approx. one turn. 2. Turn the large knurled thumb screw (44) as required to set the rip fence square against the saw table. 3. Tighten both small knurled nuts (43) again. Scale installation • Affix the self-adhesive scale (45) on the fence guide extrusion, so that the zero position is opposite of the band saw blade. For an exact alignment set the rip fence against the saw blade. 7.6 Dust collector connection ADanger! Some types of saw dust (e.g. of oak, beech and ash wood) can cause cancer when inhaled: always use a dust collector when working indoors (required air speed at the saw's suction connector . 20 m/s). A Caution! Operation without a dust collector is only possible: . outdoors; . for short-term operation (up to 30 minutes maximum); . with dust respirator. . If no dust collector is used chips will accumulate, which need to be removed periodically. Connect dust collector or industrial vacuum with a suitable adaptor to the dust extraction port. 7.7 Band saw blade tensioning ADanger! Too much tension can cause the band saw blade to break.Too little tension can cause the driven band saw wheel to slip and the band saw blade to stop. 1. Raise upper blade guide fully (see “Operation”). 2. Check tension by pushing with a finger, halfway between table and upper blade guide, against the side of the blade. The blade should flex not more than 1-2 mm. 3. Correct tension if necessary: . turning the setting knob (46) counter-clockwise increases the blade tension. . turning the setting knob (46) counter-clockwise reduces the blade tension. 7.8 Installation of the combination switch/plug 1. Fit cable bushing (47) i...
Эта инструкция также подходит к моделям:Лобзики и пилы - BAS 316G WNB (1.01 mb)