Оценок - , средний балл:
(
)
)
Производитель: Makita
Размер: 918.22 kb
Название файла: 1051.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
It chamfers up to 5.6 mm (7/32")in a single pass. I groove I I Front base I I ASSEMBLY Dust bag Install the dust bag on the nozzle of the tool. When installing it, push the bag's entry port toward the nozzle as far as it will go to prevent it from coming off during operation. For the best results, empty the dust bag when it becomes about half full. Remove the dust bag from the tool and pull out the fastener. NOTE: If you connect a Makita vacuum cleaner Model 406 to this tool, more efficient and cleaner operations can be performed. Removingor installing planer blades CAUTION: *Always be sure that the tool is switched off and the battety cartridge is removed before removing or installing the blades. *Handle the blades very carefully. Use gloves or rags to protect your fingers or hands when removing or installing the blades. To remove the blades, first loosen the two installation bolts one turn counterclockwise with the hex wrench provide. Push the blade from the belt side with the hex wrench. Remove the other blade in the same manner. To install the blades, first clean out all chips I or foreign matter adhering to the drum or blades. Insert the blade between the drum Drum cover 1 lnstalation bolts cover from the side opposite the belt so that the blade end will protrude slightly Planer blade from the side of the drum. Tighten the two installation bolts securely with the hex wrench provided. Side of drum Drum CAUTION: Use only the Makita hex wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury. Hex wrench storage When not in use, the hex wrench can be conveniently stored. OPERATION Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making any contact. Switch on and wait until the blades attain full speed. Then move the tool gently forward. Apply pressure on the front of tool at the start of planing, and at the back at the end of planing. Planing will be easier if you incline the workpiece in sta- tionary fashion, so that you can plane somewhat downhill. The speed and depth of cut determine the kind of finish. The power planer keeps cutting at a speed that will not result in jamming by chips. For rough cutting, the depth of cut can be increased, while for a good finish you should reduce the depth of cut and advance the tool more slowly. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILIW, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools- Electric': ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. High Capacity Battery charger Model DC1411 Battery cartridge 14221143411435 Mini planer blade Part No. A-90401 Edge fence (guide rule) with thumb screw and washer Part No. 344727-5 Dust bag Part No. 122469-9 High Capacity Battery charger Model DC1801 Battery cover Part No. 414938-7 ' Hex wrench Part No. 783202-0 Plastic carrying case Part No. 824544-4 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of Califomia] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: 0 Lead from lead-based paints, @ Crystalline silica from bricks and cement and other masonry products, and Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. MAKmA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from workanship and materials for the period of ONE YEAR from the date of origi...