Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 1 2 1 2 Pins 2. Edge fence (Guide rule) 1 23 1. Rear base 2. Foot 3. Planer blade 003873 Edge fence (Guide rule) Edge fence is useful for minimizing a short run of cut by cutting in a uniform width. The edge fence (guide rule) is provided on the side of the tool. Press two pins for the edge fence (guide rule) so that the edge fence appears. Move the tool forward while keeping the flat surface of the edge fence in contact with the side of the workpiece. To return the edge fence to an original position, push it upwards from its underside. 003874 Foot After a cutting operation, raise the back side of the tool and a foot comes under the level of the rear base. This prevents the tool blades to be damaged. 003875 Guideline of cutting blade passage Both ends of the front base are a guideline to show the ends of cutting blades passage. 1. Front base 1 ASSEMBLY 1 2 1. Socket wrench 2. Installation bolt 1 1. Socket wrench CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003876 Removing or installing planer blades CAUTION: • Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. • Handle the blades very carefully. Use gloves or rags to protect your fingers or hands when removing or installing the blades. • Use only the Makita wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. This could cause an injury. 003878 To remove planer blades from the drum, loosen the eight installation bolts by only one full turn with the socket wrench. Then push and slide a planer blade sideways from the belt side using the helm of the socket wrench. To remove another planer blade, follow the same procedure as above. To install the blades, first clean out all chips or foreign matter adhering to the drum or blades. 003879 1 3 2 4 5 6 7 1. Drum plate 2. Installation bolt 3. Set plate screw 4. Set plate 5. Planer blade 6. Adjusting screw 7. Drum 0 Insert the blade between the drum and the set plate from the nozzle extraction side so that the blade will be centered from both ends of the drum or set plate. First tighten the eight installation bolts lightly and evenly shifting from the center bolts to the outward bolts with the socket wrench. And then, tighten all of the installation bolts securely. Install another blade in the same manner as above. For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is set properly and securely. The blade must be mounted so that the cutting edge is absolutely level, that is, parallel to the surface of the rear base. Below are some examples of proper and improper settings. EN0004-1 (A) Front base (Movable shoe) (B) Rear base (Stationary shoe) Correct setting Nicks in surface Gouging at start Gouging at end (A) (B) (B) (A) (B) (A) Although this side view cannot show it, the edges of the blades run perfectly parallel to the rear base surface. Cause: One or both blades fails to have edge parallel to rear base line. Cause: One or both blade edges fails to protrude enough in relation to rear base line. Cause: One or both blade edges protrudes too far in relation to rear base line. 1 3 2 4 5 6 7 1 3 2 4 5 6 7 Drum plate 2. Installation bolt 3. Set plate screw 4. Set plate 5. Planer blade 6. Adjusting screw 7. Drum 1 2 3 1. Socket wrench 2. Wrench holder 3. Rear base 003879 Blade height adjustment Blade height adjustment is usually not necessary. However, if you notice that the blade edge is below the level of the rear base or protrudes too far from the rear base, proceed as follows. Loosen the eight installation bolts and the set plate screws. Turn the adjusting screws clockwise to retract the blade or counterclockwise to protrude it. After adjusting the blade height, tighten the set plate screws and the eight installation bolts securely. 003882 Socket wrench storage When not in use, store the socket wrench as shown in the figure to keep it from being lost. 12 12 At the start of planing 2. At the end of planing 1 1. Front roller 1 003884 Nozzle assembly and joint (optional accessory) Nozzle assembly and joint are used when connecting the tool to vacuum cleaner. When you wish to perform cleaner operation, connect a vacuum cleaner to your tool. To connect vacuum cleaner, remove the chip guide from the tool. Place nozzle assembly and joint in its place and then tighten screws to secure them. 003885 Connect a hose of vacuum cleaner to the joint. 1. Chip guide 1. Joint 2 1 3 2. Nozzle assembly 3. Hose OPERATION 003886 Planing operation First, rest the tool front base flat upon the workpiece surface without the blades maki...