Оценок - 3, средний балл: 3.7
(
)
)
|
Фото и характеристики Makita 1002BA |
Фрагмент инструкции
A loose installation bolt can be dangerous. Always check to see they are tightened securely. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Knob Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius of 320 mm. For concave cuts with the tool’s minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go. Then retighten the two wing bolts firmly to secure the front base. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. 1 Wing bolt CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. Sharpening planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine Sharpening holder edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. Wing nut Blade (A) Side (C) Blade (6) Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpen- ing at the same angle. MAINTENANCE CAUTlON: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. I Limit mark Use a screwdriver to remove the chip cover. 1 // Sdrewdriver Chipcover Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. I Brush holder cap \ To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Planer blade Planer blade Width 11 0 mm (4-3/8”) (Material Tungsten-carbide) Part No 793008-8 Width 110 mm (4-3/8”) Part No 7930096 Sharpening holder assembly Socket wrench Part No. 123055-9 Part No. 782209-3 *Blade gauge Part No. 123062-2 Seo.-ll-'97 US 110 mm (4-318") CURVED PLANER Model 1002BA e Note: The switch and other part configurations may differ from country to country. MODEL 1002BA Sep.-11-'97 US ,&, DESCRIPTION ';"OM EDDESCRIPTION MACHINE MACHINE ___ ~ 1 1 Pan Head Screw M4x50 33 1 Belt cover 2 1 Pan Head Screw M4x20 34 1 Ball Bearing 6200LB 3 1 Chtp Cover 35 1 Insulation Washer 4 2 Brush Holder Cap 36 1 ARMATURE ASSEMBLY 5 2 Carbon Brush (With Item 34. 35, 36 & 39) 6 2 Wing Bolt M6x25 38 1 Flat Washer 12 7 2 Spring Washer 6 39 1 Ball Bearing 6ZOlDDW 6 2 Flat Washer 6 40 1 Rubber Pin 6 9 4 Rivet 0-5 41 2 Pan Head Screw M5x65 10 1 Name Plate 42 1 Rubber Pin 4 11 1 Main Frame 43 1 FIELD ASSEMBLY 12 1 Cord 44 8 Hex Flange Head Bolt M6x17 13 1 Cord Guard 45 2 Drum Plate 14 1 Strain Relief 46 4 Pan Head Screw M4x5 15 2 Pan Head Screw M4x18 41 2 Adjusting Plate 17 1 Handle Cover 48 2 Planer Blade 1 10 18 3 Pan Head Screw M4x30 49 1 Rubber Pm 6 19 1 Bracket [With Item 40 & 491 50 1 Ball Bearing 620122 20 6 Pan Head Screw M5x28 51 1 Washer 12 21 2 Pan Head Screw M4x30 52 1 Drum 22 1 Poly V Belt 6-212 53 1 Washer 10 23 1 V Pulley 6-23L 54 1 Ball Bearing 620022 24 2 Pan Head Screw M4x6 55 1 Rubber Pin 4 25 1 Switch 56 1 Front Base 26 1 Pan Head Screw M4x12 51 1 Rubber Packmg 21 1 Fan Guide 58 1 Compression Spring 21 28 2 Pin 6 59 1 Front Box 29 2 Pan Head Screw M5x28 60 1 Flat Washer 13 30 1 Base 61 1 Knob 64 31 2 Pan Head Screw M5x18 62 1 Label 32 1 V Pullev 6 -30 Note The switch and other part specifIcattonS may dlffer from country to country MAKITA LIMITED ONE YEAR WARRANTY i Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not appl...