Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
NUT !i i. •:Q ••• :••• •• know our olnter-maner .... .... P WARNING: F_R" YOUR OWN: SAFETY TURN SWITCH 2 SLIDING GUARD INFEED TABLE SLIDE BRACKET CUTTER GUARD IIII!_1 L I 1 11: DEPTH OF CUT HANDWHEEL. Turning the handwheel counterclockwise Will lower the infeed _ table to maximum depth of 1/8 in, _.. FENCE LOCKS AND STOPS. The fence can be moved across the Jointer to take full advantage of the "sharpness" of the blades. The:fence should be positioned to the extreme right (toward pulley) but not beyond the end of the blades. Mostof the cutting (usually jointing) witl be done with the fence in this position. As the blades become dull, the fence can be moved toward the left where the blades are sharper. To move the fence, loosen the Fence Lock Knob and the Sliding Gu_ird Knob and slide to desired position. Make sure SLIDE BRACKET is even with surface of OUTFEEDTABLE. If it is above or below the surface, loosen screws and adjust it. a. Alwavstighten fence Iock knob first to align fence, then tighten sliding guard knob. 6 ON-OFF SWITCH |1,, 11 i i INFEED //_ .... _-_-../TABLE/j _ f / PUSH DOWN WHEN LOCKING FENCE LOCK KNOB FENCE 45°FENCE STOP 90° FEN, STOP FENCE \ KNOB \ 1:2 I \ DEPTH OF CUT HANDWHEEL DEPTH OF CUT HANDWHEEL SLIDING GUARD KNOB SLIDE BRACKET b. Before tightening fence lock knob, hold fence down on outfeed table so it does not rock. c. 90 ° Fence Stop positions fence square to tables. To tilt fence, loosen the two knobs .and pull the sto;p out. Tilt to desired angle and tighten both knobs. d. To set fence at 90 ° to tables, loosen the two knobs, tilt fence so t;qe stop springs back iSto place. Tilt fence back so the stop rests on the . . :.... i iiiiitJ:IH111111 . FENCE TILT SCALE. indicates the angle of the fence to the tables. When the 90 ° fence stop is cor rectly adjusted, the fence wilt be 90 ° to the table and the scale wi]l read 90 ° . To check for squareness, place an accurate square on infeed table and check fence while locked at 90 ° position. MAKE SURE 90 ° STOP IS AGAINST SLIDE BRACKET. if fence is not square to table; a, Slightly loosen fence lock knob and guard lock knob. :: table: ahcl tighten both knobs, e. 45 ° Fence Stop positions the fence at 45 ° to the tables. f. To tilt fence to 45 ° loosen the two knobs, pull 90 ° stop out, tilt fence so the 45 ° stop rests on the table g. Hold fence down on outfeed table and tighten the two knobs. SCALE i!i_ FENCE TILT 900 FENCE STOP _ SQUARE INFEED TABLE FENCE FACE CUTTER GUARD b_ Loosen 90 ° stop screw with small screwdriver and turn knurled sleeve which will cause fence to tilt. Turn sleeve in either direction until fence is square with infeed table. 45 ° STOP \ • _ SCALE ADJUSTING SCREW LOCKSCREW NOTE: If you knurled sleeve, fence square to cannot square fence loosen three screws "A" table. by turning and adjust 90°STOP TILT /SCALE c. Tighten knobs. 90° stop tockscrew and both fence lock _90 ° STOP d, If 90 ° reading on tilt scale does not line up with top surface of the slide bracket, _oosen screws holding scale and move it . . . tighten screws. A •,._ SCALE -_ ADJUSTING _ SCREW 45 ° STOP KNURLED 1 SLIDE BRACKET 900STOp t3 tO know your I'Ointer-manet ..... P FENCE HEAD OF SQUARE \ INFEED TABLE ::e. Adjust 450 stop in the same manner. NOTE: Tilt was= adjusted scale will foi _ 90 ° not require position. adjustment if it 4, CUTTER GUARD. Provides protection cutter head. It must always be in place and ing properly. over the function- CUTTER GUARD FENCE Check perly. the. guard to make sure it iS functioning pro- a. Posi.tion fence to right for maximum width of cut. b. Pass al/4 in. thick piece of wood between quard and fence. Guard must return automatically to against fence When free of the wo0d: over "rest cutterhead position" INFEED TABLE If guard'does Shooting and not return Maintenance automatically, Sections. see Trouble CROWNED CUT _. INFEEDTABLE:MUST LEL TO THE OUTFEED ALWAYS TABLE. BE PARAL- If the cut CROWNED, END of the adjusted. edge or it is an INFEED surface of the workpiece is indication that the OUTWARD table is HIGH and must be "_"-__ INFEED END TABLE HIGH ..... :, If the : : CAVE, of the _: : :Check cut edge or surface of the workpiece is CON- it is an indication that the OUTWARD END INFEED table is LOW and must be adjusted. the infeed table to determine the: "out of CONCAVE CUT INFEED TABLE LOW ' 14 :!:'/i_I:i_:i?_i;_:::' _::::i:/ :!;_:i::::}::i__:_:/!: ___::::i,: i: :_:_::ii:I:_i:: : :: ROTATE BLADE OUT OF a. Insert a pencit in space at end hold cutterguard open. of cutterhead to PENCIL WA / / __ b, Place a outfeed other. straightedge table. First (large along square or tong level) one side than along on the c. Raise infeed table until it touches straightedge. d, Sight high between or low table and condition straightedge of end of to determine infeed table. OU FEED "___-__._._ TABLE_ It is easier to adjust the infeed table while the Jointer is setting on your workbench. Do not turn the Jointer on its side or upside down to ...
Эта инструкция также подходит к моделям:Рубанки - 113.206930 (3.05 mb)