Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
1001001 -) Conform to the following Standards LVD EMC :EN60950 :EN55022 :1992+A1+A2:1993 :1995 Class B :EN50082-1 :IEC801-2 :IEC801-3 :IEC801-4 :1992 :1991 4KV CD, 8KV AD :1984 3V/m, 27MHz-500MHz :1988 0.5KV (Signal Line) 1KV (AC Mains) Supplementary Information “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and the Directive 89/336/EEC, 91/263/EEC, 92/31/EEC, 93/68/EEC” Place: Tokyo, Japan Signature: Date: April, 1997 Full Name: Mikio Moriya Position: General Manager R&D Department European Contact: Norco Declaration AB Box 7146 S-250 07 Helsingborg. Sweden This declaration is applied only for 230V model. Cautions 1. Please read this user's manual thoroughly before attempting to use this printer. After reading, keep this manual in a secure place where it can be referred to easily if necessary. 2. The contents of this user's manual are subject to partial modification without prior notice. 3. Transfer of the contents of this user's manual, either in part or in whole, without permission is strictly prohibited. 4. Do not attempt maintenance, disassembly or repairs of any parts of this printer except as indicated in this user's manual. 5. This company shall not be responsible for damages caused by improper operation or handling of this printer by the customer, or caused by the operating environment. 6. Do not attempt any operations which are not described in this user's manual. doing so could cause an accident or breakdown. 7. Data, etc. are basically temporary, and cannot be stored or preserved for extended periods or permanently by this printer. This company shall not be liable in any way for damages of loss of profits, etc. resulting from loss of data due to breakdown, repairs or inspections, etc. Please understand this point in advance. 8. If you find any points in these materials which are uncertain, are misprinted or are missing, please notify this company. 9. Please note that this company shall not be liable for any influence which may effect operation of this printer arising from 8 items above. FCC COMPLIANCE STATEMENT FOR AMERICA USERS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. EMI COMPLIANCE STATEMENT FOR CANADIAN USERS This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Use shielded cables to connect this device to computers. Any changes or modifications not expressly approved by the grantee of this device could void the use’s authority to operate the equipment. ETAT DE CONFORMITE EMI A L’USAGE DES UTILISATEURS CANADIENS Cet equipment produit et utilise l’energie a radiofrequences et s’il n’est pas installe et utilise correctment, c’est a dire en accord strict avec les instructions du fabricant, il risque de provoquer des interferences avec la reception de la radio et de la television. Le present appareil numerique n’emet pas de bruite radioelectriques depassant les limites applicables aux appareils numeriques de la classe A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada. Cet equipment est concu pour fournir une protection satisfaisante contre de telles interferences dans une installation residentielle. Cependant, il n’y a pas de garantie contre les interferences avec les receptions radio ...