1). Wiring Diagram FIG. 1 DAS-LLC Line Level Converter Installation Instructions 1. Connect a small run of 16/4 between the zone output on the Matrix Audio controller and the connector labelled “From Zone” on the DAS-LLC. 2. Connect the 16/4 wire run from the zone's keypad to the connector labelled “To Keypad” on the DAS-LLC. 3. Connect a stereo RCA cable from the Left and Right RCA jacks labelled “To Amplifier” on the DAS-LLC to the RCA inputs on the external amplifier. 4. Connect a smal

Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly within the Hub’s configuration software. Also ensure the correct Audio Type (Analog L/R, S/PDIF, or None) is selected for the relevant input. Composite Input at Display Device 1. Attach the composite cable (normally yellow) to the CVBS connector on the UDM-RX02. 2. Run the other end of the composite cable to the Composite connector (normally yellow) on the display device. Connect firmly. 3. If appropriate connect audio

The AXD-IR+ is in a UniMount wall panel that fits into most US-style single-gang enclosures. The AXD-IR+ works with AMX 38 kHz or 455 kHz IR transmitters. Note: The AXR-IRSM+ swivel-mount version is also available for wall or ceiling installations: FIG. 1 AXD-IR+ UniMount IR receiver AXD-IR+ Specifications Dimensions (HWD): 4.68" x 2.93" x 1.44" (118.87 mm x 74.42 mm x 36.58 mm) Available Colors: White (FG456-10) and Black (FG456-11) Receive Frequencies: 38 / 455 kHz (user-selectable) Mounting:

3 SWT pinout configuration Connecting SWT Speakers Wiring Diagram - Expanded Configuration Matrix Audio SWT Speakers are different from any other speaker available on the market. They allow you to control a single zone of audio without a keypad being installed. Therefore, some different wiring practices must be considered for proper operation and control. This is achieved by “daisy-chaining” from the first speaker to the second speaker. The main run of 16/4 from the controller will go directly t

The Rough-In Box allows the panel to be mounted directly to the studs/pre-wall and includes a wall box and mounting screws. Wall Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is not removed when installing the NXD into a Rough-In Box. The back box is only removed to gain access for the replacement of the Compact Flash component or upgrade to the VESA housing. Specifications CB-TP10 (FG036-10) Specifications Dimensions (HWD) • 7 3/8" x 10 3/8" x

1). IR Sensor located here Volume Level 6 pre-printed pushbuttons(with blue LED indicators) Navigation Wheel & pushbuttons Indicator LED FIG. 1 DAS-MET-6SRC Metreau 6-Source Audio Keypad The DAS-MET-6SRC is a SWT keypad, suitable for use in Matrix Distributed Audio Systems. Specifications DAS-MET-6SRC Specifications Power: 12 VDC, 125 mA Front Panel Components: • Pushbuttons - 6 tactile pushbuttons with blue LED indicators that illuminate when the source is selected, and stay lit until the sourc

Once a source has been selected, the Select Source Type screen will be displayed. The menu selection immediately defaults to the Learn IR selection in the first screen of the Select Source Type screen (FIG. 25). The source number is displayed at the top of the screen. FIG. 25 Select Source Type - Learn IR .. Learn IR will allow user to learn IR commands for the selected source .. Delay allows user to add a delay to all IR commands learned for the selected source type .. Label allows customizatio

Other sources such as Satellite Receivers, CD Players, MP3 Players, and any other IR Controlled audio source can be patched into the RCA source inputs on the rear panel (FIG. 1). Light Bar (power status) Function Buttons Power Switch & Expansion Port (RJ11) RS-232 (DB9) Receptacle Paging IN/OUT ports Antenna Inputs Audio Inputs (4 or 8) AM FM Audio Outputs (4 or 8) IR Outputs (8) Zone Outputs (4 or 8) Tango Series Audio Controllers are available in two variations: • DAS-T0804-SIG (FG1103-01) - T

Op eration/Reference Guide Tango Amplifiers DAS-TAMP4-SIG Tango 4-Channel Amplifier DAS-TAMP8-SIG Tango 8-Channel Amplifier Tango Distributed Audio Last Revised: 2/10/2010 AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP's or other AMX authorized entity. AMX warrants its products to be free of defects in material and workmanship under n

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way,