Write down the replacement date on a sticker or label by adding 5 years to the date of installation. Then attach it to the bottom of the AXB-MIDI. FIG. 6 Lithium battery and socket All control commands in AXB-MIDI memory are lost when the lithium battery is replaced. Contact your AMX dealer before you replace the lithium battery and verify that they have a current copy of the Axcess program for your AXB-MIDI. This will avoid any inadvertent loss of data or a service outage. AXB-MIDI MIDI Interfa

If you later change the device number, remove and reconnect the AXlink connector. This enters the new device number into memory. The device number takes effect only on power-up. The device can be 1 of the 255 devices in an Axcess, AXCENT, AXCENT2, or AXCENT3 system. The device number must match the device assignment in the Axcess program. AMX assigns device numbers into the following three segments: ! Cards 1 through 95 ! Boxes 96 through 127 ! Panels 128 through 255 Set the device number by set

The red TV Sensor indicator, located on the front panel, should be dark. 3. Turn the television on. 4. Turn the POT screw counterclockwise until the TV Sensor indicator lights. Then, turn the POT screw counterclockwise one full turn. 5. Turn television power off. If the TV Sensor indicator is lit, turn the POT screw clockwise until the indicator goes dark. 6. Reattach the enclosure and refasten the two screws. IR Signal Attenuation Adjustment If you experience television control problems after c

8 PCS and Axlink data and power connections .................................................................. 9 PCS and 12 VDC power supply connections ................................................................... 9 Installation .............................................................................................................. 10 Television Power Sensor Adjustment...................................................................... 11 IR Signal Attenuation Adjustment..........

Enclosure Metal with black matte finish Dimensions (HWD) 1.51" x 5.55" x 5.45" (3.84 cm x 14.10 cm x 13.84 cm) Weight 1.1 lb (0.499 kg) AXlink Power 12 VDC @ 230 mA AXB-VOL3 Three-Channel Volume Control Installation Installation DIP Switch Settings Use the device DIP switch to set the AXB-VOL3 AXlink device number. You can set it as one of 255 devices in an Axcess control system. Set the device number with the total of all ON (down) switches. As an example, the DIP switch below defines Device 12

The AXD-IR+ is in a UniMount wall panel that fits into most US-style single-gang enclosures. The AXD-IR+ works with AMX 38 kHz or 455 kHz IR transmitters. Note: The AXR-IRSM+ swivel-mount version is also available for wall or ceiling installations: FIG. 1 AXD-IR+ UniMount IR receiver AXD-IR+ Specifications Dimensions (HWD): 4.68" x 2.93" x 1.44" (118.87 mm x 74.42 mm x 36.58 mm) Available Colors: White (FG456-10) and Black (FG456-11) Receive Frequencies: 38 / 455 kHz (user-selectable) Mounting:

11. Only use attachments/accessories specified by the manufacturer. 12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way,

3 SWT pinout configuration Connecting SWT Speakers Wiring Diagram - Expanded Configuration Matrix Audio SWT Speakers are different from any other speaker available on the market. They allow you to control a single zone of audio without a keypad being installed. Therefore, some different wiring practices must be considered for proper operation and control. This is achieved by “daisy-chaining” from the first speaker to the second speaker. The main run of 16/4 from the controller will go directly t

FIG. 1 DAS-AMP4/8 amplifiers •The DAS-AMP4 is a 4-channel amp that provides 2 speaker pairs per unit. •The DAS-AMP8 is an 8-channel amp that supports an additional 4 speaker pairs per unit. Features • High-quality sound - delivers 60 watts of high-quality sound per channel. • Expandable - stack up to three Carbon XA amplifiers units per zone to allow up to 12 speaker pairs (24 channels) in a single zone. • Easy installation - SWT (Speaker Wire Technology) makes installation simple using four-con

The main run of 16/4 from the controller will go directly to the first speaker in the zone. • At the controller end, the wiring is left-to-right: L D G R. • At the speaker end, refer to the labeling on speaker PCB to ensure the correct wiring. The labelling at both ends must match or the IR control will not work (i.e.: if you used the RED wire for the Left Audio labelled “L” at the zone output, you must use the RED wire for the pin labelled “L” on the speaker connector). Note: Be sure to screw t