Note • The exposed conductor should be 5/16 inch (7 mm) to 7/16 inch (10 mm) long. – If shorter, it may cause a poor conductivity. – If longer, it may cause a short circuit. • Use a proper hex wrench for each terminal. – 4 mm: +B terminal and GND terminal – 3 mm: REM terminal and speaker terminals 2 Subwoofer system 2-subwoofer system (2 amplifi ers) 2-subwoofer system 4-speaker system plus subwoofer—5.1-channel (3 amplifi ers) Connection varies depending on the number of the speakers used in yo

Epreuve le Câblage d'Energie 1. Mise en marche le récepteur mais n'augmente pas le volume. La lumière d'energie du amplificateur devrait s'allumer. Si ne s'allume pas, révise le REM et le câble + 12 V. 2. Vous augmentez le volune du récepteur et tous les parlants devraient être en action. Sinon révise les connexions du clâvage dans l'amplificateur et les hauts-parleurs. Epreuve les Connexions du Clâvage Celle- ci épreuves assurent que les hauts-parleurs sont branchés convenablement. Si les h

The amplifier power light should come on. If not, check the REM and +12V wires. 2. Turn up the receiver volume slightly. All speakers should operate. If not, check wiring connections at amplifier and speakers. Test Speaker Connections These tests make sure the speakers are connected properly. If speakers don’t play at all, one (or both) speaker wires may be disconnected. Troubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and

PREPARATION Getting Started It’s a good idea to read all of the instructions before beginning the installation. Contents Installation Instructions.............................. 3 Wiring ........................................................ 5 Installing the Removable Faceplate .......... 6 Operating Instructions ............................... 7 CD Player Operating Instructions............ 10 MP3 Player Operation (PMP180U) ......... 12 CD Changer Controls (PMP180U) .......... 13 Care and Maint

Especificaciones Grados De Energia de CEA PS260 Salida de energia: 57 vatios RMSx2 canales a 4-ohmios @ < 1% THD+N Salida de energia adicional: 75 vatios RMS x 2 canales a 2-ohmios @ < 1% THD+N 155 vatios RMS x 1 canal a 4-ohmios @ < 1% THD+N Energia dinamica: 114 vatios x 2 canales a 4-ohmios Dimensiones: 7" X 12" X 2 ." (180mm X 302mm X 55.5mm) PS285 Salida de energia: 80 vatios RMSx2 canales a 4-ohmios @ < 1% THD+N Salida de energia adicional: 105 vatioss RMS x 2 canales a 2-ohmios @ < 1% THD

11 PS260 / PS285 / PS2130 / PS2180 Localizacion de Problemas Problema Causa Accion Correctiva No hay energia No llega energia a la terminal +12V Verifique fusibles No llega energia a la terminal REM Verifique fusible(s) de la unidad principal y el cableado Fusible quemado en la bateria Reemplace el fusible e identifique la causa del fallo Fusible quemado en el amplificador Reemplace el fusible e identifique la causa del fallo Conexion a tierra defectiva Conecte nuevamente la toma a tierra electr

Specifications CEA Power Ratings PS260 Power Output: 57 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Additional Power Output: 75 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 155 watts RMS X 1 channel (Bridged mono) into 4-ohms @ < 1% THD+N Dynamic Power: 114 watts X 2 channels into 4-ohms Dimensions: 7" X 12" X 2 ." (180mm X 302mm X 55.5mm) PS285 Power Output: 80 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Additional Power Output: 105 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 215

" (250mm X 302mm X 55.5mm) PS2130 Salida de energia: 123 vatios RMSx2 canales a 4-ohmios @ < 1% THD+N Salida de energia adicional: 165 vatios RMS x 2 canales a 2-ohmios @ < 1% THD+N 345 vatios RMS x 1 canal a 4-ohmios @ < 1% THD+N Energia dinamica: 246 vatios x 2 canales a 4-ohmios Dimensiones: 12" X 12" X 2 ." (300mm X 302mm X 55.5mm) PS2180 Salida de energia: 180 vatios RMSx2 canales a 4-ohmios @ < 1% THD+N Salida de energia adicional: 220 vatios RMS x 2 canales a 2-ohmios @ < 1% THD+N 450 vat

Input Level Control (LEVEL) The input level control matches the output of your radio to the input of the amplifier. After the installation is complete, make sure the input level control on the amplifier is turned down all the way (counter-clockwise or all the way to the left). Play a tape or CD (make sure bass and treble settings or EQ are flat) and turn the volume up slowly until you just start to hear distortion. Back the volume down just a bit. On the amplifier, slowly turn up the input level

Other uses might include limiting the low frequencies to smaller speakers (61/2", 6 X 9", etc.) by adjusting the crossover to a higher setting (80 – 100Hz). Crossover (X-OVER) The JPA series of amplifiers have built-in low-pass and highpass crossover filters for bi-amplifying the system. Adjust the crossover to accommodate your chosen installation method. Select LPF (low pass filter) when the amplifier will be driving woofers or subwoofers. Choose FULL when crossover mode is not active and the a