Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
In such states, the exclusion or limitation of this Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages. In such states, the exclusion or limitations of this Limited Warranty may not apply to you.This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state. © 2006 Directed Electronics - all rights reserved I IIm mmp ppo oor rrt tta aan nnt ttN NNo oot tte ees ss 1. Before operating your A/V selector, please read these instructions carefully. 2. Retain this manual for future reference. 3. Do not remove any WARNING stickers on the unit. 4. Ensure that A/V selector is mounted in an area where foreign objects or condensation can intrude into the selector. 5. This unit is designed to operate off 12VDC (vehicle battery). Verify the battery voltage of the vehicle prior to installation. 6. Ensure that all wiring is properly connected before operating the unit. 7. The engine of the vehicle should be left running when operating the A/V selector, to preclude running the battery down. 8. Mount the A/V selector switch in an area that does not interfere with the driver’s operation of the car and in an area that will not injure the driver or passengers during an accident. 9. Do not disassemble the unit. There are no serviceable parts within the unit. 10. Before replacing a blown fuse, turn the unit off and disconnect all power. Ensure the replacement fuse is of the same rating as the fuse being replaced. 11. If during operation the unit overheats or malfunctions, turn off the power and contact your dealer. Do NOT disassemble the unit, there are no user serviceable parts in the unit. 12. The rated operating temperature range of the unit is 0. to 70. C. Cool or warm the vehicle to within this temperature range prior to unit operation. W WWh hha aat tti iis ssI IIn nnc ccl llu uud dde eed dd • A/V selector VS102 • Power harness • Source selector (qty 1) • 2-DIN cables • 2-IR extension cables (80”) • 1-IR extension cable (195”) © 2006 Directed Electronics - all rights reserved I IIn nnt ttr rro ood ddu uuc cct tti iio oon nn Congratulations on your purchase of the world’s finest video entertainment system component. At Directed we are committed to bringing you the most technologically advanced products available. We are pleased that you chose a Directed Video product. Through years of critical testing and hand craftsmanship, we have created a wide range of video entertainment products for your viewing pleasure. To view other great products from Directed Electronics, please visit the Directed Video page at F FFe eea aat ttu uur rre ees ss This unit provides a 3-input and 3-output A/V selector system, with 3 hard wire remotes. The system is designed so that each monitor can independently control the video sources • A/V Inputs (AV1, AV2, AV3)—RCA • A/V Source Selector Switches • A/V Outputs (AV1, AV2)—DIN • Low power consumption • A/V Output (AV3)—RCA • Soft-Touch Selector • Auto lock-out when driving • Auto Turn Off with ignition switch • 3 Remote Sensor inputs for source control © 2006 Directed Electronics - all rights reserved Operation Pressing the button on the remote source selector switch will scroll the LED down consecutively. Each LED represents the video input source to be displayed to the video monitors. LED1 LED2 LED3 AV1 AV2 AV3 6 © 2006 Directed Electronics - all rights reserved Wiring Reference Guide NOTE: The BLUE wire of the Power Harness connects to the emergency brake. All A/V outputs are enabled only when this wire is grounded. The 5A fuse, that is referenced on the POWER CABLE wiring chart, is located inside the attached noise filter box. VS102 5A © 2006 Directed Electronics - all rights reserved 7 S SSp ppe eec cci iif ffi iic cca aat tti iio oon nns ss Operating voltage DC 12V (9V–16V) Operating current 230mA max @ 12V (add 750mA for each monitor connected) Idle current 27mA max Operation temperature range 0. to +70.C Audio input 0.5–2.2 Vrms ±5mVrms (33K. load) Audio output 0.5–2.2 Vrms ±50mVrms (33K. load) Video input 1.0 V p-p ±5 V p-p (75. load) Video output 1.0 V p-p ±5 V p-p (75. load) Signal-to-noise ratio -60dB or greater Function separation -45dB or greater Frequency response 20Hz ±1.0dB 100Hz ±0.5dB 1KHz 0dB (standard) 10Khz ±0.5dB 20Khz ±3.0dB Audio L/R separation -55dB or greater Audio L/R balance ±1dB or lower Dimensions 7.6(W) x 5.4(H) x 1.1(D) inches 192(W) x 136(H) x 29(D) mm Weight (main unit) 1.3 lbs (570 grams) Weight (source selector) 6 oz (55 grams) (each) NOTE: Specifications are subject to change without notice. © 2006 Directed Electronics - all rights reserved The company behind this system is Directed Electronics. Since its inception, Directed has had one purpose, to provide consumers with the fines...