Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!! Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there are some limitations which must be observed. • For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. • A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. • Changes or modifications to the device may void FCC compliance. • Infrequently used radio links should be tested regularly to protect against undetected interference or fault. • A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. BY (760) 438-7000 • FAX (760) 438-7043USA & Canada (800) 421-1587 & (800) 392-0123Toll Free FAX (800) 468-1340BRACKET CANMOUNT IN THREEPLACESLOCATION 1LOCATION 2LOCATION 3CORNER HOLE ISSHARED FORLOCATIONS 2 & 3USE SCREWS TOATTACH THEMOUNTINGBRACKETSNAP RECEIVER ONTO BRACKETPULL ANTENNASTRAIGHTMOUNTING NOTES: 1. MOUNT RECEIVER AS HIGH AS POSSIBLE FOR BEST RADIO RANGE2. KEEP RECEIVER AWAY FROM METAL OBJECTS THAT CAN DECREASE RADIO RANGE BY SHIELDING THE SIGNAL3. KEEP RECEIVER AWAY FROM MOTORS, FANS AND OTHER ELECTRICAL DEVICES THAT MAY CAUSE INTERFERENCE AND REDUCE RADIO RANGE RECEIVER CIRCUIT BOARDTERMINALSJUMPERWJ1JUMPERWJ2ANTENNAOPEN CASEWITH SMALLSCREWDRIVERNOTE: IF RELAY OPTION IS GOING TOBE CHANGED: REMOVE POWER, CUT JUMPERS, APPLY POWER, ERASE MEMORY, THEN RE- PROGRAM ALL TRANSMITTERSRELAY OPTIONJUMPER WJ1JUMPER WJ21 SECOND LATCHLATCH UNTIL RESET ++ TOGGLE ON AND OFF ++ 4 SECOND LATCHSOLIDSOLIDCUTSOLIDSOLIDCUTCUTCUTBE SURE POWER IS OFF WHEN CUTTING JUMPERS++ CAN BE RESET BY PUSHING THE PROGRAM BUTTON ONCE PROGRAMINDICATORPROGRAMBUTTONPOWERTERMINALSRELAYTERMINALSCOMN.O.N.C. ANTENNA11-17 VDC12-16 VAC 1. PRESS AND RELEASEPROGRAM BUTTON. 2. PROGRAM INDICATORWILL LIGHT IF THERE ISROOM IN MEMORY FORANOTHER TRANSMITTER. (32 TRANSMITTERS MAX.) 3. SEND SIGNAL FROMTRANSMITTER, INDICATORWILL FLICKER AS SIGNAL ISRECEIVED. 4. REPEAT THE ABOVE THREESTEPS FOR EACH ADDITIONALTRANSMITTER. NOTE: THE RECEIVER CAN MEMORIZEEACH TRANSMITTER MORE THANONCE. TO PREVENT DUPLICATEENTRIES, PROGRAM EACHTRANSMITTER INTO RECEIVERONLY ONCE. 1. PRESS PROGRAM BUTTONAND HOLD FOR ABOUT TWOSECONDS UNTIL INDICATORLIGHTS THEN RELEASE. 2. COUNT THE NUMBER OFINDICATOR BLINKS, THIS ISTHE TOTAL NUMBER OFTRANSMITTERS PROGRAMMED. PUSH UNTILINDICATOR LIGHTSNOTE: DO NOT CONTINUE TO PRESSBUTTON OR MEMORY WILL BE ERASED CAMERA& VCRN.O. COMN.C. N.O. COMN.C. N.O. COMN.C. N.O. COMN.C. ALARM PANEL CONNECTION1 SECOND RELAY OPTIONDOOR STRIKE CONNECTION4 SECOND RELAY OPTIONEXTERNAL RELAY CONNECTIONTOGGLE RELAY OPTIONSECURITY CAMERA CONNECTIONLATCHING RELAY OPTIONALARM PANELAUX. POWERN.C. OR N.O. ALARMLOOPDXR-701TERMINALSDXR-701TERMINALSDXR-701TERMINALSDXR-701TERMINALSPOWERSUPPLYRADIOPOWERXFMRELECTRICDOOR STRIKEPOWERSUPPLYEXTERNALRELAYLOADSTRIKEPOWERXFMR 1. ACTIVATE EACH TRANSMITTER, ONE AT AT TIME. 2. LISTEN FOR RELAY CLICK INRECEIVER. 3. VERIFY THAT THE DEVICE CONNECTEDTO THE RECEIVER RESPONDS. 4. TEST PORTABLE TRANSMITTERS INVARIOUS LOCATIONS TO DETERMINESYSTEM PERFORMANCE. 1. PRESS PROGRAM BUTTONAND CONTINUE TO HOLD ITTHROUGH THE COUNT OF THETRANSMITTERS. 2. CONTINUE TO HOLD THEBUTTON AFTER THE COUNTUNTIL THE INDICATOR BLINKSONE MORE TIME (ABOUTFIVE SECONDS AFTER THECOUNT). 3. ALL TRANSMITTERSPROGRAMMED INTO MEMORYWILL BE ERASED. PUSH AND HOLD BUTTONFOR FIVE SECONDS AFTERTHE TRANSMITTER COUNT ...