Оценок - 5, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
2 BS OFF : Surround Back speaker setting mode to the receiver is OFF. # Press the SETUP key again to accept the setting. • The Subwoofer re-mix setting indication “SW RE-MIX” scrolls across the display. • If subwoofer is turned OFF, subwoofer re-mix setting is not visible. $ Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the appropriate Subwoofer re-mix setting. 1 RMX ON : Subwoofer re-mix set mode to the receiver is ON. 2 RMX OFF : Subwoofer re-mix set mode to the receiver is OFF. % Press the SETUP key to accept the setting. 4Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. • In step 4 and 5, indications appear only for the selected channels of the speakers that require adjusting. 1 Press the SETUP key to begin TEST TONE. • This receiver enters the speaker volume level adjustment mode. The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or MULTI CONTROL %/fi keys. 1 AUTO 2 MANUAL 2 Press the SETUP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. § • If any of the speaker is set as OFF during SP SETUP, the TEST TONE adjustment for the speaker will be skipped. 3 Press the SETUP key. • The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers. 4 For MANUAL selection, press the SETUP key each time to select the speaker channel. 5Input the distance to the speakers. 1 Select the DISTANCE from the set up displays and press the SETUP key again. 2 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to Front Left speaker (L) : ____ feet (meters) Distance to Center speaker (C) : ____ feet (meters) Distance to Front Right speaker (R) : ____ feet (meters) Distance to Surround Right (RS) : ____ feet (meters) Distance to Surround Back Right (RB) : ____ feet (meters) Distance to Surround Back Left (LB) : ____ feet (meters) Distance to Surround Left (LS) : ____ feet (meters) Distance to Subwoofer (SW) : ____ feet (meters) 3 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select the distance to the front speakers. Indication in feet Indication in meters •The allowable setting range is 1 to 30 feet (0.3m to 9.0m), adjustable in 1 foot (0.3m) increments. 4 Press the SETUP key to accept the settings. 5 Repeat steps 3 and 4 to input the distance for each of the speakers. Contituned to next page 15 EN ENGLISH Preparing for surround sound Preparing for surround sound 6Adjust the LFE (Low Frequency Effects) level 1 Select the LFE LEVEL from the set up displays and press the SETUP key again. 2 Use the MULTI CONTROL Knob or MULTI CONTROL %/fi keys to adjust the LFE LEVEL. • The LFE LEVEL can be adjusted from 0dB to -10dB in 1dB step decrements. 3 Press the SETUP key to accept the setting. 4 Setup is complete when the EXIT indication appears. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 5 Press the SETUP key to exit the SETUP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the “INPUT” indication appears. 3 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the input level. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. 16 EN Normal playback Preparing for playback Listening to a source component Some preparatory steps are needed before starting playback. SPEAKERS ON/OFF ON/STANDBY POWER AUTO INPUT SELECTOR ON/OFF ENGLISH INPUT SELECTOR VOLUME CONTROL Turning on the receiver 1 Turn on the power to the related components. 2 Turn on the power to this receiver by pressing POWER ON/ OFF and ON/STANDBY key. Selecting the input mode If you have selected a component connected to the CD/DVD, VIDEO2, DVD/6CH jacks, make sure that the input mode setting is correct for the type of audio signal to be used. 7 Selecting MD/TAPE Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source to “MD”, follow the steps below: 1 Use the INPUT SELECTOR knob to select “TAPE”...