Оценок - , средний балл: ( )

Инструкция по эксплуатации Adcom, модель P1

Производитель: Adcom
Размер: 1.2 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

22k. Signal/noise ratio (CCIR) –113dB –110dB Power amplifier input Nominal sensitivity 800mV 906mV (Arcam gain) Input impedance 22k. 22k. Gain 31.5dB 31.5dB (Arcam gain) Preamplifier output Nominal output level 700mV Maximum output level 8V RMS Output impedance <50. Headphone output Maximum output level into 600. 5V Output impedance 4.7. General Mains voltage 115V or 230V 115V or 230V 115V or 230V Power consumption (maximum) 30VA 800VA (950VA for P35/3) 800VA Power consumption (standby) 2VA 2VA 2VA Dimensions W x D x H (including feet) 430 x 370 x 110mm 430 x 350 x 110mm 430 x 350 x 110mm Weight (net) 9.3kg 9.5kg (10.5kg for P35/3) 12.5kg Weight (packed) 11.5kg 12.5kg (13.5kg for P35/3) 15.5kg Supplied accessories mains leadCR-389 remote control2 x AAA batteries mains lead mains lead E&OE NOTE: All specification values are typical unless otherwise stated. Continual improvement policy Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice. Remote-control codes The following tables give the IR-commands accepted by the C31. Power commands Menu navigation commands Command Decimal Code Command Decimal Code Power toggle 16–12 UP 16–32 Power-on 16–123 DOWN 16–33 Power-off 16–124 SELECT 16–37 ENTER 16–87 Source selection commands Command Decimal Code Display control commands PHONO select 16–1 Command Decimal Code AV select 16–2 Display 16–59 TUNER select 16–3 DVD select 16–4 Volume control commands TAPE select 16–5 Command Decimal Code VCR select 16–6 Mute 16–13 CD select 16–7 Volume up 16–16 AUX select 16–8 Volume down 16–17 The following tables give commands accepted by the P35. Power commands Speaker control commands Command Decimal Code Command Decimal Code Power toggle 16–12 Speaker 1 toggle 16–35 Power-on 16–123 Speaker 2 toggle 16–39 Power-off 16–124 Speaker 1 on 16–43 Speaker 1 off 16–44 Speaker 2 on 16–45 Speaker 2 off 16–46 The following table gives commands accepted by the P1. Power commands Command Decimal Code Power toggle 16–12 Power-on 16–123 Power-off 16–124 Note that the C31 also responds to code 20–53 (the PLAY command for an Arcam CD player). The C31 swiches automatically to CD input on receiving this command. Troubleshooting If you are having trouble with your amplifier, check the following items. No sound Check the following: < Both the pre- and power-amplifiers are switched on. < The pre-amp. is not muted (indicated on the C31 by “Muted” being shown on the front-panel). < The selected source is generating audio (e.g., if CD is selected, then the CD is playing). < The tape input is not selected on the C31 (indicated by the light above the TAPE button being illuminated), instead of the expected source. In this case, press TAPE again to de-select the tape input. < The speaker outputs are enabled on the P35, as indicated by the lights above the SP1 and/or SP2 buttons (as appropriate) being illuminated. Sound cuts-out unexpectedly If the temperature of the internal heatsink rises above a safe level, then a thermal cut-out inside the amplifier will operate. During this time, the power indicator on the front panel flashes and the protection system temporarily removes the power to the speakers. The system will reset itself as the heatsink cools down. < With two pairs of low-impedance speakers connected (6. or less), overloads are more likely. Overloading the amplifier may cause it to shut down because of overheating. < Note that, due to the high output voltage from a CD player, it is possible to drive your amplifier at full power even though the volume is not set at maximum. See page 6. Amplifier does not switch back on All the amplifiers detailed in this handbook have a protection mechanism which is activated if you switch the unit on immediately after turning it off. If this mechanism activates, wait 30 seconds then try again to switch the unit on. Guarantee Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor. This period can be extended to five years if the completed registration card is returned to Arcam. Arcam can take no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept responsibility for damage or loss occurring during transit to or from the person claiming under the guarantee. The warranty covers parts and labour costs for two years from the purchase date (five years upon registration). After this time you must pay for both parts and labour costs. The warranty does not cover transportation costs at any time. Claims under guarantee This equipment should be packed in the original packing and returned to the dealer from whom it was purchased, or failing this, directly to the Arcam distributor in the country o...